1. Home
  2. 110281
  3. Instructions

110281 Kenmore Washer - Instructions

All Instructions for the 110281
61 - 67 of 67

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old hinge broke, door did not open and close right.
  • tntsplace.com from MCALLEN, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the screws from old hinge that had broke. The piece came right out with ease. I slid the new hinge in to the hole that it went in. No struggles with ease. Lined up the screw holes and put the screws back in. Finished! Works like a charm.
Was this helpful?
Thank you for voting!
Lid lock not engaging.
  • George E from Lakeland, GA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Unplug washer. Use scraper to depress spring steel catches under top cover of cabinet. Raise and support cover. Remove lock mechanism from cover using nut driver and remove switch and cable from spring tension clips. The last cable stay is zip tie/plug; pry it from hole in cover. Don't worry about saving this cable stay as the new switch has one pre installed. Before lowering cover place an object such as a rolled up towel over the cabinet spring catches to prevent engagement. Then lower cover. Locate two screw on back of control panel and remove with nut driver. Just below control panel on back side of cabinet is a single screw securing a small cover plate. Remove screw and plate. Lift control panel and turn it over. Locate plug for the latch switch and disconnect it. Then set control panel back in place. Raise and support top of washer again and pull faulty switch and cable assembly from washer. Attach new switch assembly to top cover and place cable into spring clip and insert plastic cable stay into hole. Route the connector through the opening the faulty one was pulled from. You may now close the top of the washer. Lift and turn over control panel connect new switch plug and set control panel back in place. Replace screws on back of panel and the small cover and screw. Plug washer power cord in and you should be done.
Read less
Was this helpful?
Thank you for voting!
My lid lock assembly was bad and therefore the washer lid would not lock to allow for washing.
  • Kelly from Petersburg, WV
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.
Was this helpful?
Thank you for voting!
did not work
  • JESUS from PORT ARTHUR, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
reemplace the lid lock assembly
Was this helpful?
Thank you for voting!
Bearing's were shot and seal leaked water every where.
  • Donald from Hedgesville, WV
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Replaced bearings, seal and new shaft. Washer never sounded this good, well I can't even tell it's running now. Very quiet. Just watch all the you tube vids on replacing seal and bearings and you shouldn't have any problems !
Was this helpful?
Thank you for voting!
Top bearing frozen and had to be cut out
  • Raymond from League City, TX
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Using instructions that came with parts and google and utube
Was this helpful?
Thank you for voting!
Bearings noisey
  • Harley from Flower Mound, TX
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set, Wrench set
Followed instruction sheet. Removd tub assembly, Laid, washer on side, removed motor and necessary wiring, removed drive shaft, bearings and seal assembly, cleaned all areas, installed new parts. Reassembled.
Was this helpful?
Thank you for voting!
All Instructions for the 110281
61 - 67 of 67