110281 Kenmore Washer - Instructions

UNPLUG WASHER FROM WALL PLUG
Watch u tube on how to remove top and also cover on top circuit compartment
First find the service book taped inside front. PLUGand read to read codes
call up the error codes flashing
the code indicated a defective lid latch.UNPUG WASHER
went through testing the switch one of the cont ... Read more acts was defective and intermittent.
UNPUG WASHER unpug J connect from circuit board remove wiring and connect from lid
new wiring harness goes back same as old one and mount new lid switch. done

I removed the 2 hose clamps connecting to the pump, removed 3 screws holding pump in place, and disconnected 2 wires plugged into pump. Put the new pump on in reverse order.

Take the old one out and put a new one in

Removed Back and top of digit front. removed water intake valve part order new part replacing was a breeze

Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre ... Read more ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.

Repair was pretty straight forward with the exception of removing the agitator. Hint, do not force it, just continue to work it until it releases. Problem was not entirely corrected, but improved.

My husband watched numerous YouTube videos before tackling it.

Follow step by step YouTube channel for this.

followed repair manual for code f51.ordered/replaced Rotor Position Sensor {RPS} disconnected and reconnected wiring harness at computer module and then put everything back together and that took care of the problem, It;s been working good since. that sensor was delivered the very next day. that was great. thank you

I got the three rubber elbows to quickly (at an additional price). They were the correct part and fit exactly. I replaced the aggravating spring clamps with new radiator-type screw clamps which made the job easier and in my opinion better. Then I devised a little hardware cloth "fence" around the bottom to the washer to keep the rat ou ... Read more t. The job is tough enough in that you must tip the washer forward to get at the lower elbows. Also probably a good idea to adjust the feet "in" as far as possible to minimize rodent access from the bottom.

I removed the two hinges in the lid by unscrewing them from the lid and sliding them out from the underside of the lid. I also needed to replace the hinge assembly in the washer body on the left side. I unscrewed the three screws in the back of the controls module and lifted the cover off. I unscrewed the furthest forward and left scre ... Read more w that went down to the hinge assembly. I then removed the trim ring around the bleach pour spout and unclipped the bleach hopper from the lid. Next I unlatched the lid assembly with a metal putty knife. Once inside I moved the bleach hopper out of the way and gained access to the left side hinge assembly. I removed the other screw holding the hinge in place and changed out the hinge assembly. I then worked backwards putting screws and pieces back in place. Finally, I installed new door hinge pins in the left and right sides to reattach the lid.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

move washer to get to backside, remove necessary screws and hoses, slid washer top over, replaced lid mechanism.

The most difficult was to lift the top up. Releasing the clips was tough to push in and it broke some porcelain. The 3 screws on the plastic instrument cover was all that was required. Track the wires and remove the plug in and pull the wires through the access hole and misc clips, a Phillips screw driver removes the plastic switch .Simpl ... Read more y place the new switch under the lid and the worst is done. Once the lid was up, 10 minutes and your done.

This is an easy one. Snap off the agitator cap with a screwdriver.
Remove the single but and agitator.
Remove 6 phillips head screws.
Lubricate the bearing and coax it off the spindle.