11027172601 Kenmore Washer - Instructions

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.

Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new

Thanks!!

Unplug the power. Unscrewed 2 screws on the backside of the console to removed the cabinet. Removed the 2 clips that releases the back panel from the cabinet. Disconnect the harness. Instead of removing the cabinet i just moved the washer drum around. Was plenty of room to work with. Next I removed the 2 screws that secured the lid switch to the cabinet. Moved the drum to use a wrench to unscrew the screw that holds the ground wire in place. Moved the drum to the back and used my fingers to find the clips holding the wire to the cabinet. Re-installed the new lid switch.

Very easy replacement. The new hose was more like a formed radiator hose and fit exactly.
Removed two screws at rear of control panel and separated the rear cabinet panel from the front cabinet enough to get to the water valve. I then disconnected the break hose from the valve by compressing the spring clamp. I then disconnected the other end from the washer water inlet by also releasing another spring clamp.
The new hose was installed using the same clamps. The cabinet was reassembled and washer tested for leaks.

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

I followed the instructions in the video on the part page (part #PS11741239), which was also conveniently linked in the item shipped email. The replacement of the part was very easy ... the hard part was balancing the washer again (kitchen floor seems to have sunk in the middle). Back to normal function without having to suffer a flood first. Thanks.

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

First I removed the old hose to ensure I ordered the correct part. When I got home from work the part had arrived by us mail. I opened the box and installed it without any modifications and within 5 mins. I hooked up the washing machine to the hot and cold water, then the drain hose. I was washing cloths within 20 mins of opening the box!

It took me awhile to figure out how to get the shell off the washer frame. (I didn't know about flipping it on its back). Once the moving parts were revealed, the water pump was staring at me with both ports. I turned the machine on and saw that the leak was coming from the pump.
1. Cut power
2. unclipped pump with pry with screwdriver
3. detatched both hoses - flood ensued
4. gently pulled pump off transmission
5. replaced pump

I reccommend doing this repair with empty tub.

Make sure you UNPLUG your washer first. It is also a good idea to remove the water intake hoses from the back to avoid damage to them or the valves.

Getting the outer panels off was the hardest part for me. There are 2 screws on the back of the function panel. You don't have to remove the screws completely, just until they are unscrewed from the bottom base. Then I gently pulled forward and up on the function panel and it flips back exposing the wiring. There is one wire harness plug that needs to be disconnected toward the center of the panel.
There are 2 large metal clips that are removed by pressing a flat head screwdriver into them. Press down and slightly toward the front of the washer and it will release the clip. Be careful, mine popped up and flew behind the washer.
Once the clips are removed you can pull the entire caging of the washer (top, front, right and left side panels as one) away from the machine. This will expose the entire innards of the washer.
In the front at the bottom is the water pump. It is very easily removed. Pinch the clamps around the hoses with a pair of pliers and move them up the hoses. Pull both hoses off the pump.
There are 2 metal clamps holding the pump in place. You can release them using a flat head screwdriver as well. Once free from clamps, the pump can be pulled straight forward to be removed.
Replace the pump with the new one, placing it in the same place and position as the old one. Attach the clamps back on. Mine were really hard to reattach as the tension was really tight.
Then slide the hoses back on and use the pliers to squeeze and slide the clamps back down the hoses to secure them to the pump.
Replace the cage of the machine. On my particular model, the front panel hooks under a metal lip and the side panels rest on them, so it was a challenge getting it back into place by myself in the small area I was working in.
Replace the metal clips on the top using the flat head screwdriver by pulling slightly toward the front of the washer and pressing down.
It was a little scary, I thought I was going to pinch myself.
Then reattach the one wire harness, flip the console back down and secure tightly.
Screw the 2 screws back in on the back of the function panel and your done. Reattach the hoses and plug in your washer.

This was my first washer repair. I did it with some sketchy online instructions for a different model washer. It took forever to get the washer open and was even more frustrating to put it back together. Changing out the pump was simple once I got in there. I saved over $100 in labor by doing this myself and in only took about 45 minutes.
I think I'm ready to open up the dryer and give it a good cleaning.

First, disconnect from power & turning off the water. Then, accessed the part by tipping the unit back enough to work. Remove the hoses by loosening the spring clamps. Here is where things got a bit sticky. The pump motor shaft had corroded enough to make removal of the pump a wrestling match of sub-WWF levels. Once forced off, additional time was spent removing corrosion from the shaft to facilitate fitting the new unit. A little lube was used here. Re-assembly was quick & washer was righted, plugged in and returned to service. It is a simple repair which can, with a little acting ability, be portrayed as a monumental task requiring super-human strength & the wisdom of Solomon. I played the part well enough to merit a huckleberry pie for my effort & sacrifice! Thanks!

First. I unplugged the washing machine from the electrical source. Then, I unscrewed the two screws in the front and the two screws on the back holding the control panel onto the washer. I lifted the control panel off and let it hang in the back of the washing machine. I unplugged the white plug connecting the control panel from the machine. I used a screw driver to pry the two giant spring like clamps and the cabinet released from the actual washing machine. At the bottom, I found the pump, unclamped the small clamps holding the pump on, pulled it off, installed the new one ( I used pliers to get the hose clamps where they needed to be) and then reversed by steps. Easy as pie and saved me a bunch of money

I used pliers to loosen the hose clamps and the small springs that hold the water pump to the water pump motor. The old pump then came off by simply pulling it off. The new was was the reverse. Everything worked well.
The biggest problem had been finding that the water pump was leaking. I first tried to fix it with epoxy but it is apparentlly made of nylon and the expoxy didn't stick well.
I am still annoyed that Whirlpool makes a water pum that leads so soon. The Whirlpool site showed my model number as non existent. Later, after purchasing the right one from this third party site, Whirlpool sent email that they found the model number and gave me a much higher replacement price for the pump.

Just changed out the old pump with the new one. It went very quick and smooth!

Inserted new drain hose thru back and snapped into place. Tipped washing machine back, clamped new hose with pliers.