1102702 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
machine wobbled violently
2 of 2 people
found this instruction helpful.
-
John from TEXAS CITY, TX
- Really Easy
- 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the
... Read more
final rod in the round holder. I asked my wife for assistance.
Read less
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people
found this instruction helpful.
-
Joseph from Kalkaska, MI
- Really Easy
- Less than 15 mins
-
Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people
found this instruction helpful.
-
Shane from CLINTON TWP, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu
... Read more
ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Read less
Was this helpful?
Thank you for voting!
Extreme imbalance
1 person
found this instruction helpful.
-
Jerry from OROVILLE, WA
- Really Easy
- 30 - 60 mins
-
Pliers
This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in l
... Read more
ess than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.
Read less
Was this helpful?
Thank you for voting!
Washer shaking and banging loudly during spin cycle
1 person
found this instruction helpful.
-
Dan from KISSIMMEE, FL
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Replaced the suspension rods
Was this helpful?
Thank you for voting!
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
1 person
found this instruction helpful.
-
Douglas from BEECH ISLAND, SC
- Easy
- 30 - 60 mins
-
Nutdriver
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this helpful?
Thank you for voting!
The washer was shaking during the spin cycle
1 person
found this instruction helpful.
-
Michele from ROCHESTER, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Exactly like the video from the website
Was this helpful?
Thank you for voting!
Banging when in spin cycle.
1 person
found this instruction helpful.
-
ROBERT from OXLY, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this helpful?
Thank you for voting!
Washer drum banging on spin cycle
1 person
found this instruction helpful.
-
David from KISSIMMEE, FL
- Really Easy
- 15 - 30 mins
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest
... Read more
part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Read less
Was this helpful?
Thank you for voting!
Worn belt
1 person
found this instruction helpful.
-
Lucas from ARKANSAS CITY, KS
- Very Easy
- Less than 15 mins
-
Socket set
Remove the guard that is held in place with two screw. Removed the old belt and rolled on the new. Watch your fingers.
Was this helpful?
Thank you for voting!
Shakes and moves | Noisy
1 person
found this instruction helpful.
-
Philip from BURIEN, WA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Followed video on your web site, and used that for ways to fix, good directions. If I was more organized it prob would of taken about an hour or less
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people
found this instruction helpful.
-
Enrique from Miami Shores, FL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w
... Read more
asher door bang shut.Took longer than expected, but each procedure was simple.
Read less
Was this helpful?
Thank you for voting!
The hot water supply hose developed a bulge that was due to blow soon.
1 of 2 people
found this instruction helpful.
-
Victor from Hathway Pines, CA
- Really Easy
- 15 - 30 mins
-
Pliers
Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wa
... Read more
ll box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.
Read less
Was this helpful?
Thank you for voting!
Making groaning noise in spin
1 of 3 people
found this instruction helpful.
-
Harold from Blaine, WA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driv
... Read more
en Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Read less
Was this helpful?
Thank you for voting!
Replace drain hose
3 of 11 people
found this instruction helpful.
-
Brian from DREXEL HILL, PA
- Easy
- 30 - 60 mins
-
Pliers
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this helpful?
Thank you for voting!