110225 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hot water inlet was cracked
1 person
found this instruction helpful.
-
daryl from Madison, TN
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Remove power and hoses. Remove five 1/4” hex head screws on back plate. Top control panel can be removed by inserting putty knife into front right and left corners of control panel. Push with enough force while lifting corners. Clips are metal so you won’t break them. Lay the control panel toward washer lid.
Two screws hold the wate ... Read more r inlet in place but remove cables from inlet valves and the cable in the middle which has a temperature sensing thermistor. Once the 2 screws are removed you can manipulate the assembly out of its slot. After new assembly installed with cables reconnected and screws in place align the plastic control panel tabs back in that are at the rear of the top before snapping the control panel back into position.
Two screws hold the wate ... Read more r inlet in place but remove cables from inlet valves and the cable in the middle which has a temperature sensing thermistor. Once the 2 screws are removed you can manipulate the assembly out of its slot. After new assembly installed with cables reconnected and screws in place align the plastic control panel tabs back in that are at the rear of the top before snapping the control panel back into position.
Read less
Was this helpful?
Thank you for voting!
Agitator would not agitate properly
1 person
found this instruction helpful.
-
Dawn from Little Rock, AR
- Easy
- 15 - 30 mins
-
Socket set
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the a
... Read more
gitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Read less
Was this helpful?
Thank you for voting!
upper agitator not spinning
1 person
found this instruction helpful.
-
roger from Delanco, NJ
- Easy
- 15 - 30 mins
-
Socket set
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself fro
... Read more
m this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
agitator stopped working
1 person
found this instruction helpful.
-
KENNETH from HAUGHTON, LA
- Really Easy
- 15 - 30 mins
-
Socket set
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
Was this helpful?
Thank you for voting!
Top of Agitator would not rotate
1 person
found this instruction helpful.
-
Depeturie from Madison, AL
- Really Easy
- 15 - 30 mins
-
Socket set
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Read less
Was this helpful?
Thank you for voting!
Top portion of agitator not turning
1 person
found this instruction helpful.
-
James from Oldtown, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I
... Read more
also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.
Read less
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person
found this instruction helpful.
-
Linda from Arnold, MD
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and w ... Read more ithin 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and w ... Read more ithin 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.
Read less
Was this helpful?
Thank you for voting!
Top of agitator was not working
1 person
found this instruction helpful.
-
David from Warren, MI
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Socket set
I basically followed the video that was available on Partselect.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator a ... Read more nd it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator a ... Read more nd it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator doggs wore out
1 person
found this instruction helpful.
-
Glenda from FUQUAY VARINA, NC
- Really Easy
- 15 - 30 mins
-
Socket set
Followed youtube video. Great instruction.
Was this helpful?
Thank you for voting!
top part ofagitator not turning.
1 person
found this instruction helpful.
-
Rodger from ANDOVER, OH
- Very Easy
- 15 - 30 mins
-
Socket set
Followed instructions on website video.
Was this helpful?
Thank you for voting!
No problem
1 person
found this instruction helpful.
-
Luu from STANTON, CA
- Really Easy
- 15 - 30 mins
-
Socket set
That OK , easy.
Was this helpful?
Thank you for voting!
Agitator was not turning properly; soap left on clothes. The teeth on the agitator dogs were worn off.
1 person
found this instruction helpful.
-
Carol from WEST LIBERTY, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse
... Read more
the process to complete the repair.
Read less
Was this helpful?
Thank you for voting!
Banging when in spin cycle.
1 person
found this instruction helpful.
-
ROBERT from OXLY, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this helpful?
Thank you for voting!
Agitator was free wheeling
1 person
found this instruction helpful.
-
Dennis from Spring Grove, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver
repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer drum banging on spin cycle
1 person
found this instruction helpful.
-
David from KISSIMMEE, FL
- Really Easy
- 15 - 30 mins
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest
... Read more
part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Read less
Was this helpful?
Thank you for voting!