110225 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Worn out Cogs
1 person
found this instruction helpful.
-
Leo from Yorba Linda, CA
- Easy
- 15 - 30 mins
-
Socket set
I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.
the rest was very straight forward.
Was this helpful?
Thank you for voting!
Top partion of agitator turned in both directions by hand and was not driven by the motor.
1 person
found this instruction helpful.
-
Charles from Lindenhurst, NY
- Easy
- 15 - 30 mins
-
Socket set
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person
found this instruction helpful.
-
Jeff from Michigan City, IN
- Really Easy
- 15 - 30 mins
-
Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re
... Read more
pair man.
Read less
Was this helpful?
Thank you for voting!
agitator wasn't moving
1 person
found this instruction helpful.
-
jose from lake forest, CA
- Really Easy
- 15 - 30 mins
-
Socket set
first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back
... Read more
on the instructions.
Read less
Was this helpful?
Thank you for voting!
Agitator stopped turning
1 person
found this instruction helpful.
-
William from Canandaigua, NY
- Easy
- 15 - 30 mins
-
Socket set
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person
found this instruction helpful.
-
Walter from Brandon, MS
- Really Easy
- 15 - 30 mins
-
Socket set
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agit
... Read more
ator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
Read less
Was this helpful?
Thank you for voting!
worn our Agit-dogs, agitator wouldn't pull clothes down
2 of 4 people
found this instruction helpful.
-
Douglas from Wetumpka, AL
- Really Easy
- 15 - 30 mins
-
Socket set
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the c
... Read more
orrect place.
Read less
Was this helpful?
Thank you for voting!
Top part of agitator quit agitating in one direction.
3 of 7 people
found this instruction helpful.
-
Eldon from Liberty Lake, WA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap rin ... Read more g.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap rin ... Read more g.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Read less
Was this helpful?
Thank you for voting!
Agitator was spinning freely
1 person
found this instruction helpful.
-
Michael from Clawson, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble
repeat process to re assemble
Was this helpful?
Thank you for voting!
would not agitate
2 of 4 people
found this instruction helpful.
-
Sheila from Greensboro, NC
- Really Easy
- Less than 15 mins
-
Wrench set
Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.
Was this helpful?
Thank you for voting!
Agitator wouldn't turn when washing clothes.
1 person
found this instruction helpful.
-
Kitty from Erie, PA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're i
... Read more
n). Replaced cogs in the same direction they came out. Very simple!!
Read less
Was this helpful?
Thank you for voting!
Agitaor does not spin anymore
1 person
found this instruction helpful.
-
ZHAN from MORRISVILLE, NC
- Really Easy
- Less than 15 mins
-
Socket set
First take the top cover off, second using socket to turn the nut loose at the center, then removing the plastic holder which has four directional cogs in it, replacing them with new one.
Was this helpful?
Thank you for voting!
washer would not agitate
1 person
found this instruction helpful.
-
Marius from Buena Park, CA
- Easy
- Less than 15 mins
-
Pliers, Socket set
basically pop off the top spindle cover, reach in and pull off the water cap from the agitator cog cover, unscrew the bolt holding the cog holder and pull the agittator assembly up and off the machine. Remove the piece holding the gogs in place and replace cogs making sure to put them back in the same direction as they came out. Turn the
... Read more
agitator upside down and stick the piece holding the cogs in and snap it in. Replace all components in reverse order they were removed, and there you are. Works great.
Read less
Was this helpful?
Thank you for voting!
Top part of agitator was skipping/not turning
1 person
found this instruction helpful.
-
Mike from Lakewood, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator
... Read more
from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again
Read less
Was this helpful?
Thank you for voting!
agitator didn't turn
1 person
found this instruction helpful.
-
marsha from challis, ID
- Really Easy
- Less than 15 mins
-
Socket set
I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder p
... Read more
art, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!
Read less
Was this helpful?
Thank you for voting!