110225 Kenmore Washer - Instructions

All Instructions for the 110225
76 - 90 of 408

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water drained but would not spin.
2 of 2 people found this instruction helpful.
  • Ramona from MESA, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.
Was this helpful?
Thank you for voting!
The top agitator was not spinning
2 of 2 people found this instruction helpful.
  • Alec from Indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
I popped the dispenser cap off, pulled off the plastic cover that sits on top of the agitator directional cogs assembly, and used a socket wrench with 2 extensions on it to unscrew the nut holding the assembly in place. I misplaced my socket screwdriver and rather than try to buy a nutdriver that matched the size, I just bought a little 3 /8" socket extension kit (I needed about 8" of length to be able to use a normal socket wrench). My hands are pretty big so I just had to use pliers to pull the agitator cogs assembly out. Next I just turned the assembly upside down, slipped the plastic ring off that holds the cogs in place, and put the new cogs in place of the old ones. Reassembly was just as easy. The job took about 15 minutes, and once everything was back together the agitator worked like it was brand new.
Was this helpful?
Thank you for voting!
water inlet valve was bad
2 of 2 people found this instruction helpful.
  • Francis from CPE GIRARDEAU, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
followed the instructions on the video, very easy install
Was this helpful?
Thank you for voting!
Washer made high-pitched sounds during the filling stages.
2 of 2 people found this instruction helpful.
  • Greg from GLASGOW, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Trying to follow the instructions according to the video was easy enough until the part where I had to remove the control panel for access to the screws holding the inlet valve. I don't have a putty knife, so I had a bit of trouble trying to remove the panel. I found another way. There are screws on the left and right sides which hold the control panel to the side pieces holding it to the body. If you remove the screws and use a pick or flathead screwdriver to carefully pull up on the tabs below the screws while gently pulling the control panel away, it will easily pop off with a rotational movement. The panel is centered into its location via two plastic pins molded into the side panels, so be aware of them and try to avoid breaking them. They'll help you get the panel properly positioned during reassembly, which is simple. You'll see all this easily if you take the time and look. Don't be in a rush. To reassemble, line up the panel with the plastic pins and rotate it into position. The tabs slide easily into position and lock the panel into place. Just don't forget to reinstall the screws. Removing the panel in this manner added a bit of time to the repair, but not a lot. It's still a fast repair overall. Everything else was exactly like in the video. Well, almost. I had no difficulty whatsoever with sliding the new valve into place. But once the job was done the sounds coming from the washer during the filling stages ceased. Turns out the screens in the inlet valve were getting stopped up with lime.
Was this helpful?
Thank you for voting!
Washer would not step through the cycle steps, would not complete the washer cycle.
2 of 2 people found this instruction helpful.
  • Walter from CLAYTON, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.

Problem is resolved, saved almost $250 by doing it myself!
Was this helpful?
Thank you for voting!
Washer not agitating
2 of 2 people found this instruction helpful.
  • Dianne from WALES, MI
  • Very Easy
  • Less than 15 mins
  • Socket set
Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.
Was this helpful?
Thank you for voting!
Replaced the dog ears.
2 of 2 people found this instruction helpful.
  • Todd from Milwaukee, WI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
Was this helpful?
Thank you for voting!
Top half of agitator would not agitate.
2 of 2 people found this instruction helpful.
  • Chris from Kernersville, NC
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts i n 72 hours. $10.00 bucks and never left the house.
Was this helpful?
Thank you for voting!
Found seal had split on agitator cap
3 of 5 people found this instruction helpful.
  • Kim from Cleveland, OH
  • Really Easy
  • Less than 15 mins
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .
Was this helpful?
Thank you for voting!
Agitator cogs all broken
2 of 2 people found this instruction helpful.
  • Kelly from AMARILLO, TX
  • Very Easy
  • Less than 15 mins
  • Socket set
Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put b ack in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.
Was this helpful?
Thank you for voting!
Agitator not moving
2 of 2 people found this instruction helpful.
  • Kevin from ALBUQUERQUE, NM
  • Very Easy
  • Less than 15 mins
  • Socket set
Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes
Was this helpful?
Thank you for voting!
The cold water side of the inlet wasn’t working.
2 of 2 people found this instruction helpful.
  • Valerie from FRANKFORT, KY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I figured out through the process of elimination that the problem was the rubber plunger that the solenoid opens and closes. I couldn’t fix just the plunger so I replaced the whole water inlet valve and the cold water worked perfectly after that. Even though it was a little tough to diagnose the problem it was very easy to replace the par t once I found out what it was that was wrong.
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people found this instruction helpful.
  • Raymond from BRISTOL, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Timing tabs securing the agitator center
2 of 2 people found this instruction helpful.
  • Keith from Mount Vernon, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round cente r cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
All Instructions for the 110225
76 - 90 of 408