110225 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
OEM water valve was allowing water to drip into the drum with no power to the valve.
4 of 4 people
found this instruction helpful.
-
Scott from STILWELL, KS
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed two 1/4” screws from the backside of control panel. Plastic putty knife slide under front of control panel to release the clips and allowing panel removal. Shut water supply off and removed both hot/cold hoses from valves. Removed the two T-20 screws which allowed the removal of the existing leaking valve assembly. Installed in re
... Read more
verse and it worked perfectly!!
Read less
Was this helpful?
Thank you for voting!
screeching noise at times,Wouldn't spin out
4 of 5 people
found this instruction helpful.
-
Jerry from LENGBY, MN
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Was this helpful?
Thank you for voting!
making noise when starting spin cycle
4 of 5 people
found this instruction helpful.
-
JERRY W. from CARROLLTON, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Watch video on the site and the insulation will be easy and take about 30 min.
Was this helpful?
Thank you for voting!
Washer struts were wore out
5 of 8 people
found this instruction helpful.
-
Michael from GEORGETOWN, KY
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Removed the old and replaced with new
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people
found this instruction helpful.
-
Kristy from Lebanon, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
Washer BANGING
3 of 3 people
found this instruction helpful.
-
Edwin from Mountain Home, AR
- Really Easy
- 30 - 60 mins
Believe me, I was hesitent, but after I did it, it was easy peasy, so forget the lack of confidence and dive right in.
Was this helpful?
Thank you for voting!
Washer walking during spin cycle
3 of 3 people
found this instruction helpful.
-
Tricia from HARLEYSVILLE, PA
- Easy
- 30 - 60 mins
-
Socket set
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF ... Read more I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Read less
Was this helpful?
Thank you for voting!
Burning smell, ASSUMED it was the belt
4 of 6 people
found this instruction helpful.
-
James from MAHWAH, NJ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this helpful?
Thank you for voting!
The water inlet valve on the cold side wasn’t allowing color water flow
3 of 3 people
found this instruction helpful.
-
Linda from Lebanon, VA
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I watched the video and for the most part the first part of the repair went well. I carefully stored the screws, but despite what the video suggested the part did NOT just slide out. Upon further inspection I discovered two small screws in the top of the valve housing affixing it to the machine. Since it was to narrow an are to use a driv
... Read more
er I was forced to remove the housing that holds the timer, which involved removing the knob and a small screw. On each side of the housing was a metal clip and true to form I was able to loosen one side but the other the clip launched into orbit. After a thorough inspection of the floor I found said clip. I was then able to remove the housing and loosen the two screws. Of interest is the fact that the new part had molded places for screws different that the video. After that replacing everything went smoothly and I was able to hook up the washer as the repair was successful.
Read less
Was this helpful?
Thank you for voting!
Lid strike broke
3 of 3 people
found this instruction helpful.
-
Anna from TAWAS CITY, MI
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed old one (2 screws) slid in place and screwed in.
Was this helpful?
Thank you for voting!
Top agitator did not work
3 of 3 people
found this instruction helpful.
-
George from Danbury, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the a
... Read more
gitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Read less
Was this helpful?
Thank you for voting!
Top section of agitator was slipping.
3 of 4 people
found this instruction helpful.
-
Stephen from Hot Springs, AR
- Really Easy
- 15 - 30 mins
-
Nutdriver
I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not
... Read more
perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.
Read less
Was this helpful?
Thank you for voting!
On Spin cycle washer jumping all over the place.
2 of 2 people
found this instruction helpful.
-
Tuan from LADSON, SC
- Really Easy
- 15 - 30 mins
-
Socket set
Just follow the video! Very easy.
Was this helpful?
Thank you for voting!
Water drained but would not spin.
2 of 2 people
found this instruction helpful.
-
Ramona from MESA, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.
Was this helpful?
Thank you for voting!
Washer would not step through the cycle steps, would not complete the washer cycle.
2 of 2 people
found this instruction helpful.
-
Walter from CLAYTON, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 ... Read more philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 ... Read more philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
Read less
Was this helpful?
Thank you for voting!