110224 Kenmore Washer - Instructions

All Instructions for the 110224
91 - 105 of 1246

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water Inlet Valve
14 of 16 people found this instruction helpful.
  • Ron from Hibbing, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
Was this helpful?
Thank you for voting!
water leaking from pump
15 of 19 people found this instruction helpful.
  • michael from westmoreland city, PA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
Th e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Was this helpful?
Thank you for voting!
improper or no hot water flow
16 of 23 people found this instruction helpful.
  • Cynthia from Manchester, MO
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars inst ead of hundreds for a new machine.
Was this helpful?
Thank you for voting!
Noisy, clunk at end of spin cycle, spin cycle wobble, leaked
15 of 20 people found this instruction helpful.
  • GREGG from LIVONIA, MI
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
Followed instructional video, you guys have the best repair videos!
Was this helpful?
Thank you for voting!
would not spin properly even with new coupling
16 of 24 people found this instruction helpful.
  • david from o, AL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towa rds me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Was this helpful?
Thank you for voting!
Lid switch broke away from top.
13 of 15 people found this instruction helpful.
  • Brad from Wilmington, DE
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Replaceing the actual switch was easy as unscrewing two screws with the lid up. The wiring was a different story. I guess you can cut and spice and be done with it but to get to the real connection, a lot has to come apart or have very long arms to reach from the bottom. I first removed the cover to the dials by removing the side trim and a screw at each end near the base. That exposed the wire connection. The wire actually runs under the top therefore I had to remove the back panel partially to gain access to the wiring and holders for the wire. Just by remembering the steps while backing out, everything worked out.
Was this helpful?
Thank you for voting!
Washer vibrates excessively on spin cycle
13 of 15 people found this instruction helpful.
  • Glenn from PROVO, UT
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and di d that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.
Was this helpful?
Thank you for voting!
Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.
17 of 27 people found this instruction helpful.
  • Matthew from Albany, MN
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from trans mission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test
Was this helpful?
Thank you for voting!
water leaking during run cycle
13 of 15 people found this instruction helpful.
  • michael from weymouth, MA
  • Really Easy
  • 15 - 30 mins
  • Pliers
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer
Was this helpful?
Thank you for voting!
Machine would stop at spin cycle
13 of 15 people found this instruction helpful.
  • Steven from COHOES, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..
Was this helpful?
Thank you for voting!
washer would no longer fill to proper height--just low
13 of 16 people found this instruction helpful.
  • keith from Bellaire, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed top controls panel (not obvious),then released old switch by rotating 90 degrees (after disconnecting wires and pressure sensor tubing), then reinstalled new switch (new switch has only 3 positions, not 5 as old switch had) and reinstalled everything else.

A 'gotcha' is the plastic 'strap' on the back that anchors swit ch compartment to the back steel sheet. It is EASY to dislodge that plastic strap from the bakc panel and it drops down inside the panel--maybe to the floor, maybe not--requiring difficult retrieval. Suggest TAPING the plastic strap in place on the back steel sheet so it will not fall out.
Was this helpful?
Thank you for voting!
Will Not Spin
13 of 16 people found this instruction helpful.
  • Daniel from Temple, TX
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
This is a relatively new washer and failed early. My previous whirlpool washer lasted 20 years without any repairs. 1. First inquired about the spin problem in partselect. Machine will not sping unless manualy forced then it will take off but weak. 2. Partselect suggested a clutch problem. Ordered the part that came fast. When I tr ied removing the shaft hub with a hammer and chisel it will not get loose so I opted ordering the special wrench to loosen the tub hub. 3. I put the machine on its back and loosened the pump retaining clips. Do not remove the hoses from the pump. Move the pump away from the motor shaft. Remove the motor electrical connector and set aside. 4. Remove the three bolts holding the gearbox-motor assemply and pull it out of the tub. 5. Put the assembly on a towelwith shaft up and remove the separator washer from the old clutch that is sitting on the gearbox. Then remove the c-retaining clip from the shaft. 6. Pry out the wire retaining clip from the clutch and pull the old clutch out of the shaft. 7. The clutch kit I ordered came with a plastic brake to clutch cam so I replaced it too, just remove the retainig clip from the brake that is at the bottom of the tub and replaced the part. 8. Installed the new clutch and the retaining clips in reverse order. Replace all parts that came with the kit. The new clutch spring was already in place. 9. Put the assembly back into the tub and re-install all the other items in the same order. It spins good now! 10. While replacing parts, methodically clean all the lint from the motor and from under the machine. The gearbox showed signs of leaking oil so its a question of cost. I left it there until it fails then I'll buy a new machine.
Was this helpful?
Thank you for voting!
lid would not lock, washer would not run...
12 of 13 people found this instruction helpful.
  • John from Hale Center, Texas, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this helpful?
Thank you for voting!
The top lid switch failed so washer wouldn't run.
11 of 11 people found this instruction helpful.
  • Katherine from Salem, VA
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Removed the valance by unscrewing nuts on top back and then removing side wings. The valance can be flipped up and hung over the back of the backsheet making sure not to damage clear hose. Then remove the old switch, wire and cut off the ground wire. Moount the new switch and make sure the wire is well back from the drum by tying to the o ld clip that held the old wire. Connect the ground to the body now under the valance. I found a hole there and screwed the ground terminal to it with a self taping screw.This procedure allows you to replace the switch without having to take the complete washer front body off.
Was this helpful?
Thank you for voting!
Water inlet nozzle was stripped and leak
24 of 50 people found this instruction helpful.
  • Armand from WESTPORT, MA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
Was this helpful?
Thank you for voting!
All Instructions for the 110224
91 - 105 of 1246