110224 Kenmore Washer - Instructions

All Instructions for the 110224
121 - 135 of 1246

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hot water valve would barely open - take 35 mins to fill washer
10 of 11 people found this instruction helpful.
  • Kevin from ARLINGTON, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Pull the washer out from wall
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Was this helpful?
Thank you for voting!
My drain hose had cracked and was leaking.
10 of 12 people found this instruction helpful.
  • Miguel from San rafael, CA
  • Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Once I finally found the part I needed, the repair was very simple and took only a few minutes. Thanks to the very helpful operator to walk me through the diagram to find the corresponding number for the part. I really appreciate your help!
Was this helpful?
Thank you for voting!
Tub banged against the front of case during spin
9 of 9 people found this instruction helpful.
  • Peter from Boca Raton, FL
  • A Bit Difficult
  • Less than 15 mins
  • Screw drivers
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Was this helpful?
Thank you for voting!
Washer would not spin a full load.
11 of 15 people found this instruction helpful.
  • Ralph from Newbury Park, CA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people found this instruction helpful.
  • Larry from HICKORY, NC
  • Very Easy
  • Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people found this instruction helpful.
  • Elzoria from FROSTPROOF, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
Machine agitated during cycle but would not spin clothes dry.
10 of 13 people found this instruction helpful.
  • Kurt from Bremerton, WA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.
Was this helpful?
Thank you for voting!
Spin cycle not working properly; Clothes still soaked when spin cycle finished
12 of 19 people found this instruction helpful.
  • Sarah from Columbus, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing complet ely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.
Was this helpful?
Thank you for voting!
Washer tub off balance and noisy
9 of 10 people found this instruction helpful.
  • Gregory from Kent, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverag e with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Was this helpful?
Thank you for voting!
there was a hole in the original drain hose
10 of 14 people found this instruction helpful.
  • Kathy from Pittsburgh, PA
  • Really Easy
  • Less than 15 mins
  • Pliers
First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new ho se onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!
Was this helpful?
Thank you for voting!
Timer was bad.
12 of 20 people found this instruction helpful.
  • Gary from Maple Grove, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed 4 screws holding the trim and timer mechanism.There is 1 phillips screw holding the timer to remove,and a plastic piece to pull out from the back of the timer.I easily pulled it off,and the timer fell right off.I removed the wiring harness,and removal was done.Installing the timer was a reversal of the process.Slide the timer in place.install 1 screw,snap wiring harness on.push timer dial on,shroud back in place and 4 screws to put back in. The whole process took me 15 minutes,and is a very simple fix.My wife was thrilled,and I was the hero!
Was this helpful?
Thank you for voting!
Washer basket off-center and wobbling during spin cycle
8 of 8 people found this instruction helpful.
  • Craig from Woodland Hills, UT
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.
Was this helpful?
Thank you for voting!
Severe wobble during spin cycle.
9 of 11 people found this instruction helpful.
  • Steven from Dallas, GA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spr ing bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
Was this helpful?
Thank you for voting!
Direct drive pump was leaking
8 of 8 people found this instruction helpful.
  • Philip from DENTON, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.
Was this helpful?
Thank you for voting!
Slow Spin Cycle with Fast/Normal Agitator
8 of 8 people found this instruction helpful.
  • Michael from AURORA, CO
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Socket set
My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!
Was this helpful?
Thank you for voting!
All Instructions for the 110224
121 - 135 of 1246