110224 Kenmore Washer - Instructions

All Instructions for the 110224
76 - 90 of 1246

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not spin
24 of 40 people found this instruction helpful.
  • floyd from Slidell, LA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people found this instruction helpful.
  • Dennis from Oak Island, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
Cold water flow was slow
22 of 36 people found this instruction helpful.
  • Garry from Palm Bay, FL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syph on to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people found this instruction helpful.
  • Paul from Painesville, OH
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Noise, all the lubricant had leaked from the gearcase.
15 of 15 people found this instruction helpful.
  • larry from SOD, WV
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
DO NOT do this repair from the top. The only thing needed to be removed from the top of the machine is the agitator and retaining clip. After removing these items, lay the machine on its front, on a table if you have a friend who will help. Remove the back cover. Simply disconnect the wiring, remove the water pump, the tub locking mec hanism, the belt, and motor. Remove the four bolts holding the gearcase. It should come out with little effort. Remove the old tub seal. There should be a new one on the replacement. Lubricate the new seal. Dishwashing liquid worked great. Move the drive wheel from the old gearcase to the replacement part. All the parts originally removed will only fit one way. Reverse all the removal steps and you be should be ready to go. My only problem with the replacement was there was no groove in the new part spline for the tub retaining clip. Seemed to be no problem since the agitator is bolted on so the tub is going nowhere.
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people found this instruction helpful.
  • Steve from Cypress, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!
Washing machine leaking water
16 of 19 people found this instruction helpful.
  • John from Oklahoma City, OK
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
Was this helpful?
Thank you for voting!
Lid Switch broke had to replace.
15 of 16 people found this instruction helpful.
  • Michael from Litchfield, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
The biggest problem for me was finding the screws to remove the control panel. First there are two screws on the top back side of the control panel, then there are plastic covers that have to be removed from both sides of control panel, then you can remove the screws at the base of the control panel. Set the control panel back, then re move the golden brackets that hold the cabinet to back of the washer. The whole cabinet will come forward with a little coaxing. (Remember to put the screws with the part you have removed to make sure you put them back in the same place.) Next remove screws that hold on the lid switch, remove wiring from clips, then replace with new switch, situate wiring in clips, position switch into place, screw into place. The cabinet is really hard to get back into place, be patient it may take a few tries. Once you get the cabinet in place, replace the golden brackets, then place the control panel where the screw holes line up and screw down, replace plastic sides, then replace the screws in the back side and your done.
Was this helpful?
Thank you for voting!
Smelled a burning odor occasionally
17 of 23 people found this instruction helpful.
  • Paul from E NORTHPORT, NY
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set, Wrench (Adjustable)
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Was this helpful?
Thank you for voting!
Washer lid would not release
18 of 26 people found this instruction helpful.
  • Michael from BURLINGTON, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people found this instruction helpful.
  • Chuck from South Holland, IL
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
my cold water did not run in the machine and it would not rinse
15 of 18 people found this instruction helpful.
  • TONYA from DISTRICT HEIGHTS, MD
  • Easy
  • Less than 15 mins
  • Screw drivers
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
washer overflowing
17 of 24 people found this instruction helpful.
  • GREIG from CARTERSVILLE, GA
  • Easy
  • Less than 15 mins
  • Screw drivers
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.
Was this helpful?
Thank you for voting!
No cold water supply/slow cold water fill
14 of 15 people found this instruction helpful.
  • Andrew from Virginia Beach, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs a nd moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.
Was this helpful?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
17 of 24 people found this instruction helpful.
  • Kevin from Disputanta, VA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Was this helpful?
Thank you for voting!
All Instructions for the 110224
76 - 90 of 1246