110224 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Tank was overfilling, lots of water on the floor, not good.
34 of 39 people
found this instruction helpful.
-
Jonathan from Hayden, ID
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Disassembled the control panel and replaced the water level sensor, but not the hose - bad idea. It was probably just the hose. The thing tested fine for 3 fillings. I told my friend to watch it closely for the first couple of loads, because I thought the level was not consistent? - but she didn't. More water on the floor. Replaced the h
... Read more
ose and it's working fine. Thank you.
Read less
Was this helpful?
Thank you for voting!
Water would not fill the washer except for 4 inches.
38 of 52 people
found this instruction helpful.
-
Patricia from MURPHYSBORO, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load
Was this helpful?
Thank you for voting!
old switch broke off
33 of 38 people
found this instruction helpful.
-
Clay from Flower Mound, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
The new switch was quite different than the old, so I wasn't sure it was the right part. On closer examination, I saw it had been greatly improved and strengthened. I merely unscrewed the old switch, cut the wires, and installed the new switch, using wire nuts to rewire it. This switch is clearly a good fix for a weak design. Sure gla
... Read more
d I found partselect.com!
Read less
Was this helpful?
Thank you for voting!
Excessive tub wobble, tubs leaning forward of normal
31 of 33 people
found this instruction helpful.
-
David from GLEN BURNIE, MD
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found
... Read more
that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.
While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.
At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.
Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.
While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.
At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.
Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
unbalanced load...knocking sound.
32 of 37 people
found this instruction helpful.
-
Edward from Easthampton, MA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, sc
... Read more
rew). Reassembled washer then ran wash for a cycle. Successful fix.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Found cracked brake shoe
33 of 41 people
found this instruction helpful.
-
Michael from Trafalgar, IN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, the
... Read more
n used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.
Read less
Was this helpful?
Thank you for voting!
Washer would fill/empty but would not agitate nor spin
30 of 35 people
found this instruction helpful.
-
Ted from SOUTH MILWAUKEE, WI
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.
Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.
Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.
Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.
Replaced clips to hold motor on transmission and reinstalled screws holding clips.
IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!
Attach pump onto motor and replace clips. Double check everything is back in place.
Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.
First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.
Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.
Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.
Replaced clips to hold motor on transmission and reinstalled screws holding clips.
IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!
Attach pump onto motor and replace clips. Double check everything is back in place.
Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.
First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Read less
Was this helpful?
Thank you for voting!
Severe water leak
27 of 29 people
found this instruction helpful.
-
Noel from Pollock, ID
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp ... Read more s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp ... Read more s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
Read less
Was this helpful?
Thank you for voting!
Lid would not register closed washer would not spin
30 of 38 people
found this instruction helpful.
-
william from HOLLEY, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Remove top of washer 5min R&R cable 20 min total time 25 min.
Was this helpful?
Thank you for voting!
Two leaking hoses in my washing machine
29 of 39 people
found this instruction helpful.
-
Marc from Morton Grove, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
water overflowing when filling
34 of 54 people
found this instruction helpful.
-
Marni from Buhl, ID
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly d
... Read more
ifferent configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Over shaking and knocking on the side
25 of 28 people
found this instruction helpful.
-
Alain.m from HARLINGEN, TX
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was r
... Read more
eally happy so me. It can be done by anybody but first go on the internet to get a idea.
Read less
Was this helpful?
Thank you for voting!
Water constantly dripped into washer when it was off.
24 of 25 people
found this instruction helpful.
-
MARK from MARION, MA
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat ... Read more er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat ... Read more er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
Read less
Was this helpful?
Thank you for voting!
Waher would not spin and made noise
25 of 29 people
found this instruction helpful.
-
Andrew from SYLVANIA, OH
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install
... Read more
and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Read less
Was this helpful?
Thank you for voting!
Agitator was locked up
24 of 28 people
found this instruction helpful.
-
Roger from Palmyra, IN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two ho
... Read more
ses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger
Read less
Was this helpful?
Thank you for voting!