11021392010 Kenmore Washer - Instructions

All Instructions for the 11021392010
46 - 60 of 89

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burning smell, ASSUMED it was the belt
4 of 6 people found this instruction helpful.
  • James from MAHWAH, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this helpful?
Thank you for voting!
Stripped screws on a hub drive replacement
3 of 3 people found this instruction helpful.
  • Bruce from GLOBE, AZ
  • Easy
  • 15 - 30 mins
  • Screw drivers
Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.
Was this helpful?
Thank you for voting!
Lid lock not working.
5 of 9 people found this instruction helpful.
  • James from LIVONIA, LA
  • Very Easy
  • 15 - 30 mins
  • Socket set
Followed instructions.
Was this helpful?
Thank you for voting!
washer was draining but no spinning
3 of 3 people found this instruction helpful.
  • JOSE from MILLBURY, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Was this helpful?
Thank you for voting!
washer would not spin on wash cycle
3 of 3 people found this instruction helpful.
  • Kim from MOUNT UNION, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.
Was this helpful?
Thank you for voting!
Not really a problem but the hardest part was moving the washer to lay on its back.
2 of 2 people found this instruction helpful.
  • John from WHITEWATER, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people found this instruction helpful.
  • John from TEXAS CITY, TX
  • Really Easy
  • 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people found this instruction helpful.
  • Tracy from CONWAY, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people found this instruction helpful.
  • Joe from SAN JOSE, CA
  • Very Easy
  • Less than 15 mins
  • Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Was this helpful?
Thank you for voting!
On Spin cycle washer jumping all over the place.
2 of 2 people found this instruction helpful.
  • Tuan from LADSON, SC
  • Really Easy
  • 15 - 30 mins
  • Socket set
Just follow the video! Very easy.
Was this helpful?
Thank you for voting!
out of balance
2 of 2 people found this instruction helpful.
  • Charles from ARVADA, CO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
The info. was really helpful
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
Washer wasn’t spinning fast enough to get the water out and it had a slight burning electrical smell.
2 of 2 people found this instruction helpful.
  • craig from Oxford, CT
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
I simply followed your clutch drive repair video on YouTube, that wasn’t the problem so I replaced the motor… remove the cover that goes over the drive belt by taking out the two screws, remove the belt, unplug the wire connector going to the motor and remove the two bolts that hold it up and it falls right into your hand. Then reverse the process and that’s it. Very easy repair.
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people found this instruction helpful.
  • Raymond from BRISTOL, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people found this instruction helpful.
  • Tom from LONG BEACH, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp ool washers!
Was this helpful?
Thank you for voting!
All Instructions for the 11021392010
46 - 60 of 89