11021392010 Kenmore Washer - Instructions

All Instructions for the 11021392010
31 - 45 of 89

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid lock/latch stuck closed
6 of 7 people found this instruction helpful.
  • David from BELMONT, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Watched a video
Was this helpful?
Thank you for voting!
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
8 of 14 people found this instruction helpful.
  • TERRY from WAUKEE, IA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Was this helpful?
Thank you for voting!
heavy loads did not spin dry properly
6 of 8 people found this instruction helpful.
  • Chet from CLEARWATER, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Was this helpful?
Thank you for voting!
water would drip into tub between uses
5 of 5 people found this instruction helpful.
  • Dale from MANDAN, ND
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged washer, turn off water to washer, removed water lines from washer, pull washer away from wall, removed about 5 screws from top access panel and remove, used putty knife to release clips from both sides of front control panel and lay forward, removed three screws from valve, disconnect hose from valve. Reassemble in reverse order . Not a bad idea to run a little water into bucket from both supply line to remove any foreign material that may have let lose from shut off valve before reconnecting to washer.
Was this helpful?
Thank you for voting!
Loose pulley
7 of 11 people found this instruction helpful.
  • Joseph from BAKER, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Tightened up the pulley as the video showed me that might be the issue.
Was this helpful?
Thank you for voting!
The washer stopped draining.All the pump motor did was hum.
5 of 6 people found this instruction helpful.
  • Michael from Staten Island, NY
  • Easy
  • 1- 2 hours
  • Pliers, Socket set
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machin e worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Was this helpful?
Thank you for voting!
The capacitor exploded, broke the plastic cover that held it to the body of the machine and blow itself clear of the wires
4 of 4 people found this instruction helpful.
  • Jay from AMELIA CT HSE, VA
  • Very Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed the back access panel and what was left of the capacitor mounting device (the capacitor (or what was left of it) was laying against the access panel). I mounted the new capacitor which had a metal strap for mounting. I removed the small, black, wire mounting device that was still plugged in to the old capacitor and slipped the wires through that device. After reviewing how to reattach the wires (it turned out the polarity on my capacitor did not matter) I plugged the wires in using the wire mounting device. Once I closed it back up everything worked fine.
Was this helpful?
Thank you for voting!
Making a loud noise for a while then stopped spinning
4 of 4 people found this instruction helpful.
  • Lucas from ARKANSAS CITY, KS
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this helpful?
Thank you for voting!
Lid wouldn't lock
4 of 4 people found this instruction helpful.
  • James from INDIAN LAKE, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!
making noise when starting spin cycle
4 of 5 people found this instruction helpful.
  • JERRY W. from CARROLLTON, GA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Watch video on the site and the insulation will be easy and take about 30 min.
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people found this instruction helpful.
  • Kristy from Lebanon, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
3 of 3 people found this instruction helpful.
  • Maxwell from RINGWOOD, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.

I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Was this helpful?
Thank you for voting!
washer shaking
3 of 3 people found this instruction helpful.
  • Oralia from DALLAS, TX
  • Easy
  • 30 - 60 mins
  • Pliers
the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23
Was this helpful?
Thank you for voting!
Washer walking during spin cycle
3 of 3 people found this instruction helpful.
  • Tricia from HARLEYSVILLE, PA
  • Easy
  • 30 - 60 mins
  • Socket set
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Was this helpful?
Thank you for voting!
Actuator clicking not going into spin mode
3 of 3 people found this instruction helpful.
  • Courtney from Hollis, NH
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.
Was this helpful?
Thank you for voting!
All Instructions for the 11021392010
31 - 45 of 89