110203 Kenmore Washer - Instructions

All Instructions for the 110203
76 - 90 of 100

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
3 of 5 people found this instruction helpful.
  • Michael from Cranford, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I followed the video published on this site
Was this helpful?
Thank you for voting!
Wouldn't fill with water.
2 of 2 people found this instruction helpful.
  • Wes from WARRIOR, AL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Part fixed it perfectly.
Was this helpful?
Thank you for voting!
Washer made high-pitched sounds during the filling stages.
2 of 2 people found this instruction helpful.
  • Greg from GLASGOW, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Trying to follow the instructions according to the video was easy enough until the part where I had to remove the control panel for access to the screws holding the inlet valve. I don't have a putty knife, so I had a bit of trouble trying to remove the panel. I found another way. There are screws on the left and right sides which hold the control panel to the side pieces holding it to the body. If you remove the screws and use a pick or flathead screwdriver to carefully pull up on the tabs below the screws while gently pulling the control panel away, it will easily pop off with a rotational movement. The panel is centered into its location via two plastic pins molded into the side panels, so be aware of them and try to avoid breaking them. They'll help you get the panel properly positioned during reassembly, which is simple. You'll see all this easily if you take the time and look. Don't be in a rush. To reassemble, line up the panel with the plastic pins and rotate it into position. The tabs slide easily into position and lock the panel into place. Just don't forget to reinstall the screws. Removing the panel in this manner added a bit of time to the repair, but not a lot. It's still a fast repair overall. Everything else was exactly like in the video. Well, almost. I had no difficulty whatsoever with sliding the new valve into place. But once the job was done the sounds coming from the washer during the filling stages ceased. Turns out the screens in the inlet valve were getting stopped up with lime.
Was this helpful?
Thank you for voting!
Would not Agitate
2 of 2 people found this instruction helpful.
  • Scott from HILBERT, WI
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Tip the washer on its back remove the agitator install new one under 15 minutes
Was this helpful?
Thank you for voting!
Washer would not step through the cycle steps, would not complete the washer cycle.
2 of 2 people found this instruction helpful.
  • Walter from CLAYTON, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.

Problem is resolved, saved almost $250 by doing it myself!
Was this helpful?
Thank you for voting!
violent basket wobble
3 of 5 people found this instruction helpful.
  • Keith from DUNBARTON, NH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
remove basket and replace drive hub kit
Was this helpful?
Thank you for voting!
no water to washer
2 of 2 people found this instruction helpful.
  • Donald from LINN CREEK, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Socket set
a couple of issues to get valve out and off , 15 min. install and top back on!!!
Was this helpful?
Thank you for voting!
water inlet valve was bad
2 of 2 people found this instruction helpful.
  • Francis from CPE GIRARDEAU, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
followed the instructions on the video, very easy install
Was this helpful?
Thank you for voting!
broken lid latch
2 of 2 people found this instruction helpful.
  • James from CLINTON TWP, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
move washer to get to backside, remove necessary screws and hoses, slid washer top over, replaced lid mechanism.
Was this helpful?
Thank you for voting!
Replaced the suspension springs
2 of 3 people found this instruction helpful.
  • Dave from EUSTIS, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
The video was excellent in what needed to be accomplished. However it showed reaching inside the tub with vise grips to grab the old spring. This worked fine for removing them but the installation of the new spring did not allow my hand and vise grip to secure the new spring and pull it up and insert it into the retainer. I found that by taking a cord and putting it through the socket and retainer allowed me to pull straight up and seat it in the retainer a lot easier.
Was this helpful?
Thank you for voting!
The washer kept filling with water during the cycles
2 of 3 people found this instruction helpful.
  • Latchmin from DORAL, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug the washer.
Turn of the water.
Remove the hoses.
using a 1/4 inch nut driver, remove the screws from the back panel.
Remove the console by inserting a putty knife between the console and the top until you hear the click.
Unplug the harness for the inlet valve.
remove the two screws holding the inlet va lve and then remove the inlet valve.
Replace with new inlet valve and affix with the two screws.
Plug in the electrical harness.
Place Console back into position.
Place back panel into position and tighten screws with nut driver.
Put the hoses back on the inlets.
turn the water back on.
plug in the washer.
Was this helpful?
Thank you for voting!
Reolaced actuator
2 of 3 people found this instruction helpful.
  • Thomas from New Fairfield, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1. Unplugged the electrical cord
2. Unscrewed the plastic guard
3. Unscrewed the actuator screws
4 Unplugged the cord.
5. Replaced the olld one with the new one and reversed the order
6. Uprighted the machine
7 Performed trail run with vinegar
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people found this instruction helpful.
  • Shane from CLINTON TWP, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this helpful?
Thank you for voting!
Door alignment
2 of 4 people found this instruction helpful.
  • Amy from INMAN, SC
  • Really Easy
  • 30 - 60 mins
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people found this instruction helpful.
  • Enrique from Miami Shores, FL
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w asher door bang shut.Took longer than expected, but each procedure was simple.
Was this helpful?
Thank you for voting!
All Instructions for the 110203
76 - 90 of 100