110203 Kenmore Washer - Instructions

Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.

Watch video on the site and the insulation will be easy and take about 30 min.

Turned off power and water. Removed hoses/Unplugged power. Removed screws to open and access control panel. Removed existing valve first by pinching off 6 wire connectors then screws securing valve to washer base. At this point, I replaced with new valve and reattached everything. I also added screen washers to both hoses as I suspect i ... Read more t was built up debris in original valve impeding water flow through valve that led to problem…

My husband watched numerous YouTube videos before tackling it.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

Watched and followed You Tube Video . "Solved: The Fix for a Whirlpool Washing Machine that won't fill with water." The video is a little over 8 minutes long. At that start of the video he encourages you to watch all of the video for special instructions near the end of the video. You need to do that! I put 30-60 minutes, but actual ... Read more time was 4 days as I had to order parts and wait for the parts to arrive.

I watched the video and for the most part the first part of the repair went well. I carefully stored the screws, but despite what the video suggested the part did NOT just slide out. Upon further inspection I discovered two small screws in the top of the valve housing affixing it to the machine. Since it was to narrow an are to use a driv ... Read more er I was forced to remove the housing that holds the timer, which involved removing the knob and a small screw. On each side of the housing was a metal clip and true to form I was able to loosen one side but the other the clip launched into orbit. After a thorough inspection of the floor I found said clip. I was then able to remove the housing and loosen the two screws. Of interest is the fact that the new part had molded places for screws different that the video. After that replacing everything went smoothly and I was able to hook up the washer as the repair was successful.

Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I alre ... Read more ady had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.

Take the old one out and put a new one in

Removed old one (2 screws) slid in place and screwed in.

Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.

Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 c ... Read more heaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.

Part fixed it perfectly.

Ordered the part for the 500 series Kenmore washer open the top switch the two parts out and reconnected the new part replace the covers they only thing is cold is hot and the hot is cold even with it connect correct I just put on opposite settings and go with it

Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 ... Read more philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.

Problem is resolved, saved almost $250 by doing it myself!