11020022014 Kenmore Washer - Instructions

All Instructions for the 11020022014
76 - 90 of 434

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced the dog ears.
2 of 2 people found this instruction helpful.
  • Todd from Milwaukee, WI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.
Was this helpful?
Thank you for voting!
Top half of agitator would not agitate.
2 of 2 people found this instruction helpful.
  • Chris from Kernersville, NC
  • Really Easy
  • Less than 15 mins
  • Pliers
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts i n 72 hours. $10.00 bucks and never left the house.
Was this helpful?
Thank you for voting!
Easy to install
2 of 2 people found this instruction helpful.
  • John from LEXINGTON, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I just drained the washer and unscrewed the 3 screws unhooked the hose clamp and installed the new one attached the hose and hose clip. Really easy. Took longer to try up water in floor than installing.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people found this instruction helpful.
  • Tom from LONG BEACH, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp ool washers!
Was this helpful?
Thank you for voting!
Washer hoses due for replacement
3 of 5 people found this instruction helpful.
  • James from PINE MOUNTAIN, GA
  • Easy
  • 30 - 60 mins
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this helpful?
Thank you for voting!
agitator was making a large amount of noise
2 of 2 people found this instruction helpful.
  • Timothy from Kansas City, MD
  • Easy
  • 15 - 30 mins
  • Socket set
After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!
Was this helpful?
Thank you for voting!
Agitator seperated from inside of wash drum
2 of 2 people found this instruction helpful.
  • Larry from Brandon, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing vi deo. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.
Was this helpful?
Thank you for voting!
Not really a problem but the hardest part was moving the washer to lay on its back.
2 of 2 people found this instruction helpful.
  • John from WHITEWATER, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this helpful?
Thank you for voting!
My washer was always off balance.
2 of 2 people found this instruction helpful.
  • Tracy from CONWAY, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
Belt needed to be replaced
2 of 2 people found this instruction helpful.
  • Raymond from BRISTOL, CT
  • Really Easy
  • 30 - 60 mins
  • Socket set
Took the Cover off and installed belt.
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people found this instruction helpful.
  • John from TEXAS CITY, TX
  • Really Easy
  • 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this helpful?
Thank you for voting!
Upper agitator not turning.
2 of 2 people found this instruction helpful.
  • David from MILLBRAE, CA
  • Really Easy
  • 30 - 60 mins
  • Socket set
Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting no ise. Reassemble. The drawing on this site is helpful.
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people found this instruction helpful.
  • Shane from CLINTON TWP, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this helpful?
Thank you for voting!
Water leak into washer drum
2 of 3 people found this instruction helpful.
  • Richard E from BURKE, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the water inlet valve. Easy install… figured it out on my own, but checked the instructional online video to make sure it was done right.
Was this helpful?
Thank you for voting!
the top section of the agitator would not turn
2 of 3 people found this instruction helpful.
  • joseph from san antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
Was this helpful?
Thank you for voting!
All Instructions for the 11020022014
76 - 90 of 434