- Home
- 11020022013
- Instructions
11020022013 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer wouldn't start - Flashing Lid Light
13 of 20 people
found this instruction helpful.
-
Marc from HOPE MILLS, NC
- Easy
- 30 - 60 mins
-
Screw drivers
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Read less
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people
found this instruction helpful.
-
Elzoria from FROSTPROOF, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
replaced drain hose that was missing
12 of 20 people
found this instruction helpful.
-
Delmar from EAST TROY, WI
- Really Easy
- 30 - 60 mins
-
Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
Top section of the agitator would not work properly
12 of 20 people
found this instruction helpful.
-
James from Crownsville, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the top cap, unbolted the agitator, lifted off the top section, removed old "dogs" and replaced new "dogs", reinstalled agitator and tested.
Was this helpful?
Thank you for voting!
With full load, clothes were not agitating correctly - very little action or movement of the upper agitator section.
8 of 8 people
found this instruction helpful.
-
Douglas from Lancaster, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Took off softener dispenser, pried off top of agitator, removed bolt from top of agitator.
Then pulled out the agitator assembly for easier access.
Used screwdriver to brake small plastic keepers holding secondary agitator ratchet clutch to the secondary agitator.
Assembled and inserted new ratchet mechan ... Read more ism in the top of the agitator, making sure 4 small square pegs protruding from the end of the new assembly fully entered into mating holes on the secondary agitator.
Placed the agitator back on the agitator post and installed and secured bolt. Replaced cap and installed softener dispenser.
Then pulled out the agitator assembly for easier access.
Used screwdriver to brake small plastic keepers holding secondary agitator ratchet clutch to the secondary agitator.
Assembled and inserted new ratchet mechan ... Read more ism in the top of the agitator, making sure 4 small square pegs protruding from the end of the new assembly fully entered into mating holes on the secondary agitator.
Placed the agitator back on the agitator post and installed and secured bolt. Replaced cap and installed softener dispenser.
Read less
Was this helpful?
Thank you for voting!
I followed the video guide, which was excellent
7 of 7 people
found this instruction helpful.
-
Richard from NAPLES, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.
Machine works great now.
Machine works great now.
Was this helpful?
Thank you for voting!
washer is unbalanced during a spin cycle
7 of 7 people
found this instruction helpful.
-
Tiffany from NORTH OLMSTED, OH
- Really Easy
- Less than 15 mins
I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.
Was this helpful?
Thank you for voting!
Shaking extreme
7 of 7 people
found this instruction helpful.
-
Barbara from RICHMOND, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Per instruction sent with purchase
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people
found this instruction helpful.
-
Larry from Edgewood, TX
- Really Easy
- Less than 15 mins
-
Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Making noise when spinning tub hit side of washer.
7 of 8 people
found this instruction helpful.
-
Ernestine from CARRIERE, MS
- Really Easy
- 30 - 60 mins
-
Socket set
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this helpful?
Thank you for voting!
washer wasn't spinning on final spin
7 of 8 people
found this instruction helpful.
-
Terry from HANCOCK, MD
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this helpful?
Thank you for voting!
Washer gets stuck on Rinse and not complete the cycle.
6 of 6 people
found this instruction helpful.
-
Charles from SEALY, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.
Unfortunately, this new latch assembly did not fix the problem.
Was this helpful?
Thank you for voting!
Rotation cogs (4) worn out and the upper part of the agitator wouldn't turn with the lower agitator.
6 of 6 people
found this instruction helpful.
-
David from LOVELAND, CO
- Really Easy
- 15 - 30 mins
-
Socket set
Popped the cap off the agitator (pocket Knife) Look down in the center of the agitator. I saw I needed a 7/16 socket, 6" extention and ratchet. I used 1/4" drive. I took the retaining bolt out and lifted the upper portion of the agitator off of the iower portion and out of the tub. Set the part I took out on the dryer. I pulled the cone s
... Read more
haped part that houses the 4 cogs pieces out of the center of the upper agitator part. Once the coned shaped part was out, turned it upside down and placed it on the closed washing machine lid, then again used my pocket knife to lift the plastic retaining ring that securely holds the 4 cogs in place upward on the cone as to remove and replace the 4 worn out cogs with the new ones purchased in a repair kit. Pay close attention the direction the old cogs are facing, so the new ones go back in the same facing direction. It can be extremely easy to install the new ones backwards. I have to say at this point, I was quite disappointed with the retrofit repair kit I purchased. The new cone part the holds the cogs and goes down into the center of the upper agitator wouldn't allow the bolt that locks the whole agitator to the shaft to line up straight and wanted the bolt to "cross" thread into the main shaft. I took it all apart again and reused the original coned shaped part that came with the machine. I should have purchased just the 4 cogs for considerably less money. Reassembled the cone part and put it back together. Reinstalled the upper agitator in reverse order of removing it. Turned on the washer and it works like it's supposed to once again. Hope this helps the next person.
Read less
Was this helpful?
Thank you for voting!
Lid lock/latch stuck closed
6 of 7 people
found this instruction helpful.
-
David from BELMONT, MI
- Really Easy
- 30 - 60 mins
-
Nutdriver
Watched a video
Was this helpful?
Thank you for voting!
Lid wouldn't lock
4 of 4 people
found this instruction helpful.
-
James from INDIAN LAKE, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!