11020022012 Kenmore Washer - Instructions

All Instructions for the 11020022012
91 - 105 of 407

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My washer was always off balance.
2 of 2 people found this instruction helpful.
  • Tracy from CONWAY, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this helpful?
Thank you for voting!
Loud banging during spinning
3 of 5 people found this instruction helpful.
  • Tom from LONG BEACH, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlp ool washers!
Was this helpful?
Thank you for voting!
machine wobbled violently
2 of 2 people found this instruction helpful.
  • John from TEXAS CITY, TX
  • Really Easy
  • 30 - 60 mins
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this helpful?
Thank you for voting!
Upper agitator not turning.
2 of 2 people found this instruction helpful.
  • David from MILLBRAE, CA
  • Really Easy
  • 30 - 60 mins
  • Socket set
Removed agitator cover with small screwdriver. Removed bolt holding agitator with socket on 6" extender. Pulled agitator up and out. Replaced thrust spacer adding tiny amount of silicone grease. Replaced agitator directional cogs adding small amount of silicone grease. Note direction of cogs first or they will make a loud ratcheting no ise. Reassemble. The drawing on this site is helpful.
Was this helpful?
Thank you for voting!
Not really a problem but the hardest part was moving the washer to lay on its back.
2 of 2 people found this instruction helpful.
  • John from WHITEWATER, CA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this helpful?
Thank you for voting!
Rinse cycle kept repeating, did not spin clothes
2 of 3 people found this instruction helpful.
  • Shane from CLINTON TWP, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actu ator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this helpful?
Thank you for voting!
washer shake hole machine from begin spin about 11/2 ' h
3 of 6 people found this instruction helpful.
  • Dieu from Houston, TX
  • A Bit Difficult
  • 30 - 60 mins
chage out part and washer still shake
Was this helpful?
Thank you for voting!
Agitator would not agitate
2 of 3 people found this instruction helpful.
  • Daniel from Beaufort, SC
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Removed the agitator with a socket wrench and replaced cogs as directed in repair video.
Was this helpful?
Thank you for voting!
agitator broke
2 of 3 people found this instruction helpful.
  • Joseph from Kalkaska, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this helpful?
Thank you for voting!
Top part of agitator not working
2 of 3 people found this instruction helpful.
  • Roger from St. Albans, WV
  • Easy
  • Less than 15 mins
  • Nutdriver
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
Was this helpful?
Thank you for voting!
Top Agitator would turn
2 of 3 people found this instruction helpful.
  • EDWARD from CATONSVILLE, MD
  • Easy
  • Less than 15 mins
  • Socket set
First, I unscrewing the single bolt which keeps the two part agitator in place (agitator bolt). Second, I pulled the entire agitator out from the machine. third, I then seperated the top and bottom parts of the agitator. forth, I removed the old worn out "Agitator Direction Cogs". Fifth, I then inserted the new Agitatpr Direction Co gs"s. Six, I reassembling the top and bottom parts of the agitator. Seven, I reinstalled the reassembled agitator back into the machine. Eight, after inserting and tighting up the agitator bolt with a socket rench, and tured the machine on, it work like it was new again. .
Was this helpful?
Thank you for voting!
the top section of the agitator would not turn
2 of 3 people found this instruction helpful.
  • joseph from san antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.
Was this helpful?
Thank you for voting!
Top agitator would not agitate
2 of 3 people found this instruction helpful.
  • Michael from Clarksville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
The repair was very simple. I removed the agitator cap with a small screw driver, removed the retainer screw with a socket set tool. I removed the top agitator, lifted the cam and removed the old worn directional cogs installed the new ones. I reassembled the agitator. All of 10 minutes.... Very easy
Was this helpful?
Thank you for voting!
Replaced cogs in agitator
2 of 3 people found this instruction helpful.
  • Allen from Simpsonville, KY
  • Really Easy
  • Less than 15 mins
Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.
Was this helpful?
Thank you for voting!
Washer Agitator not working properly
1 person found this instruction helpful.
  • Carleen from Las Vegas, NV
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking th e agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix
Was this helpful?
Thank you for voting!
All Instructions for the 11020022012
91 - 105 of 407