11020022012 Kenmore Washer - Instructions

All Instructions for the 11020022012
61 - 75 of 407

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The washer would walk across the floor
4 of 5 people found this instruction helpful.
  • William from BROOKFIELD, WI
  • Very Easy
  • 30 - 60 mins
  • Socket set
Watched the video. It was by far the easiest repair I've ever done. The washer is happy and stays in it place
Was this helpful?
Thank you for voting!
Burning smell, ASSUMED it was the belt
4 of 6 people found this instruction helpful.
  • James from MAHWAH, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this helpful?
Thank you for voting!
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
3 of 3 people found this instruction helpful.
  • Maxwell from RINGWOOD, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.

I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Was this helpful?
Thank you for voting!
washer would not spin on wash cycle
3 of 3 people found this instruction helpful.
  • Kim from MOUNT UNION, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.
Was this helpful?
Thank you for voting!
Washer walking during spin cycle
3 of 3 people found this instruction helpful.
  • Tricia from HARLEYSVILLE, PA
  • Easy
  • 30 - 60 mins
  • Socket set
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Was this helpful?
Thank you for voting!
washer shaking
3 of 3 people found this instruction helpful.
  • Oralia from DALLAS, TX
  • Easy
  • 30 - 60 mins
  • Pliers
the repair went well but I still haven't received a refund for the order was was sent incorrectly. Order #22085769 order date 2/3/23
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people found this instruction helpful.
  • Kristy from Lebanon, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
Actuator clicking not going into spin mode
3 of 3 people found this instruction helpful.
  • Courtney from Hollis, NH
  • Easy
  • 30 - 60 mins
  • Pliers, Socket set
I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.
Was this helpful?
Thank you for voting!
Top agitator did not work
3 of 3 people found this instruction helpful.
  • George from Danbury, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the a gitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Was this helpful?
Thank you for voting!
Lid lock not working.
5 of 9 people found this instruction helpful.
  • James from LIVONIA, LA
  • Very Easy
  • 15 - 30 mins
  • Socket set
Followed instructions.
Was this helpful?
Thank you for voting!
Auger part of agitator not pulling down clothes.
4 of 6 people found this instruction helpful.
  • Jeffrey from CAMP HILL, PA
  • Very Easy
  • Less than 15 mins
  • Socket set
Popped off agitator cover discovered worn and broken 'dogs'. Decided to replace complete agitator assembly due to age of machine (25 + years). 7/16 socket, removed nut and agitator assembly, installed new assembly with included nut.
Was this helpful?
Thank you for voting!
Broken agitator top section...
3 of 3 people found this instruction helpful.
  • Dan from GREAT FALLS, MT
  • Really Easy
  • Less than 15 mins
  • Socket set
Removed softener cup agitator cap and one bolt, lifted agitator out and replaced with new one... tightened bolt replaced cap and softener cup and away we go, done...
Was this helpful?
Thank you for voting!
washer was draining but no spinning
3 of 3 people found this instruction helpful.
  • JOSE from MILLBURY, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Disconnect electrical plug from the wall, disconnect drain hoses and tip washer forward remove belt hosing basket and then remove the electrical plug that contains seven wires connected to actuator then remove the two small screws.
Then reverse the operation to stall the new part. Very easy.
Was this helpful?
Thank you for voting!
Top section of agitator was slipping.
3 of 4 people found this instruction helpful.
  • Stephen from Hot Springs, AR
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.
Was this helpful?
Thank you for voting!
Agitator seperated from inside of wash drum
2 of 2 people found this instruction helpful.
  • Larry from Brandon, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing vi deo. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.
Was this helpful?
Thank you for voting!
All Instructions for the 11020022012
61 - 75 of 407