- Home
- 1068670331
- Instructions
1068670331 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
refrigerator stopped cooling due to condenser over-heating
1 of 2 people
found this instruction helpful.
-
Kevin from COVINGTON, LA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
Was this helpful?
Thank you for voting!
Nonr
1 of 2 people
found this instruction helpful.
-
Gaynell P from Spring, TX
- Really Easy
- Less than 15 mins
Replaced missing stud.
Was this helpful?
Thank you for voting!
Broken shelf supports
1 of 2 people
found this instruction helpful.
-
Bob from Las Vegas, NV
- Really Easy
- Less than 15 mins
Took just a few moments to install. The parts fit like a glove,
Was this helpful?
Thank you for voting!
Both front wheels were severly damaged needing replacement.
1 of 2 people
found this instruction helpful.
-
James from Leesburg, VA
- Easy
- 15 - 30 mins
-
Socket set, Wrench (Adjustable)
I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.
Was this helpful?
Thank you for voting!
Motor noise while running and clicking when shutting off
1 of 2 people
found this instruction helpful.
-
Curtis from Sedona, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this helpful?
Thank you for voting!
Old tube had cracked due to being frozen....
1 of 3 people
found this instruction helpful.
-
Stephen from Greensboro, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
I followed the simple steps outlines in the great video! Thanks
Was this helpful?
Thank you for voting!
Every time we opened the fridge everything in the door shelf would fall out
1 of 3 people
found this instruction helpful.
-
Jeremy from New Berlin, WI
- Really Easy
- Less than 15 mins
This website saved my marriage. For the past two years, every time we would open the fridge everything in the door shelves would fall all over the floor. This was not only embarassing when we would have family and friends over but I really got tired of my wife yelling every time she would open up the fridge. I tried every type of glue
... Read more
and repairs to try and fix it, finally gave up and thought the only way I would find peace at home was to purchase a new fridge. I accidently stumbled across your website and before I knew it and about $6 later my life improved more than you can imagine. The best part was how easy it was to find the part I needed with the detailed pictures you have. The part was shipped fast and very easy to install. I will definately use partselect again. Thanks!
Read less
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people
found this instruction helpful.
-
James from Howell, MI
- Easy
- 30 - 60 mins
-
Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people
found this instruction helpful.
-
Jeremy from State College, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl
... Read more
aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Read less
Was this helpful?
Thank you for voting!
you have to turn it off and on to run.
0 of 1 people
found this instruction helpful.
-
chris from woodland hills, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this helpful?
Thank you for voting!
Freezer shelf falling off
1 of 4 people
found this instruction helpful.
-
Carl from Crete, IL
- Really Easy
- Less than 15 mins
-
Pliers
One of the front studs was broken off. I had to use pliers to pull it out (kind of tight). Then I inserted the back and front holders and layed the shelf back in. Total time...10 min
Was this helpful?
Thank you for voting!
Part broke.
0 of 1 people
found this instruction helpful.
-
Felix A from Orlando, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Replacement partfit perfectly.
Was this helpful?
Thank you for voting!
end cap broke when shelf was overstocked
0 of 1 people
found this instruction helpful.
-
Walter from Gloucester City, NJ
- Really Easy
- Less than 15 mins
removed broken parts then installed new parts job was done.
Received parts the next day after ordering.
Thanks
W Hertlein
Received parts the next day after ordering.
Thanks
W Hertlein
Was this helpful?
Thank you for voting!
The fill tube froze and cracked
0 of 1 people
found this instruction helpful.
-
Phillip from Sellersburg, IN
- Easy
- Less than 15 mins
-
Nutdriver, Wrench (Adjustable)
It was easy and quick to find the part that I needed, order it and have it shipped. The fill tube arived in 3 days and was easy to replace.
Was this helpful?
Thank you for voting!
the front wheel broke
0 of 1 people
found this instruction helpful.
-
Mary from Pelham, NY
- Easy
- Less than 15 mins
-
Screw drivers
First I had to tilt the refrigerator on wood on the supports under the refrigerator, the wheels were easy to get to then I unscrewed the old ones and replaced them with the new better wheels. The old ones where plastic.
Was this helpful?
Thank you for voting!