- Home
- 1068670331
- Instructions
1068670331 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
3 of 6 people
found this instruction helpful.
-
Joseph from Chesterfield, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.
Thanks so much! You saved me a bundle!!
Thanks so much! You saved me a bundle!!
Was this helpful?
Thank you for voting!
refrigerator was overheating, condensor fan dead.
2 of 3 people
found this instruction helpful.
-
David from Granada Hills, CA
- Really Easy
- 15 - 30 mins
First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade ... Read more ,
reinstalled cover, plugged it in and BAM .WORKS PERF!
Read less
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people
found this instruction helpful.
-
Douglas from Mesa, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
compressor not running
1 person
found this instruction helpful.
-
Doug from Lancaster, CA
- Really Easy
- 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people
found this instruction helpful.
-
Richard from North Easton, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi
... Read more
er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Read less
Was this helpful?
Thank you for voting!
door hinge broke.
2 of 4 people
found this instruction helpful.
-
Bernard from DONALDSONVLLE, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed door and replaced bushing bracket was ok.
Was this helpful?
Thank you for voting!
Broken kickplate retainers
1 person
found this instruction helpful.
-
Joe from STRATFORD, OK
- Very Easy
- Less than 15 mins
-
Screw drivers
replaced retainers. remove and replace four(4) phillips screws.
Was this helpful?
Thank you for voting!
No cold
1 person
found this instruction helpful.
-
Jacqueline from LEXINGTON PK, MD
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
Connection leaked as tube entered freezer
1 person
found this instruction helpful.
-
Robert from MERRIMACK, NH
- Very Easy
- 15 - 30 mins
Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.
Was this helpful?
Thank you for voting!
One of the front wheels was broken in half.
1 person
found this instruction helpful.
-
John from INNSBROOK, MO
- Very Easy
- 15 - 30 mins
-
Nutdriver
Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done
Was this helpful?
Thank you for voting!
freezer quit working
1 person
found this instruction helpful.
-
Anthony from CIRCLEVILLE, OH
- Really Easy
- Less than 15 mins
-
Pliers
replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
Was this helpful?
Thank you for voting!
Shelf studs broke several years ago and I had a problem locating them. Finally wised up and checked Part Direct and found them, ordered the kit w/ 12 pieces. Then quickly watched the installation video. Took less than 30 minutes to replace two different studs. Wife is very happy.
1 person
found this instruction helpful.
-
Karl from BIRDSBORO, PA
- Easy
- 15 - 30 mins
-
Pliers
Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.
Was this helpful?
Thank you for voting!
freezer would not freeze
1 person
found this instruction helpful.
-
Michael from HELENDALE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic
... Read more
k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Read less
Was this helpful?
Thank you for voting!
Plugged it in.
1 person
found this instruction helpful.
-
Adam from GLOVERSVILLE, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 people
found this instruction helpful.
-
MATTHEW from STOCKTON, CA
- Really Easy
- Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!