1068670331 Kenmore Refrigerator - Instructions

All Instructions for the 1068670331
91 - 105 of 202

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer occasionally had a temperature alarm.Clicking noise also.
1 person found this instruction helpful.
  • Barry from FORD CITY, PA
  • Really Easy
  • Less than 15 mins
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this helpful?
Thank you for voting!
compressor clicks on for about 5 seconds and then shuts off, evaporator fan is running but no cooling in the fridge.
1 person found this instruction helpful.
  • Scott from Jay, ME
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Disconnect power. Remove back panel on the refrigerator. Relay and overload is a modular unit attached to the compressor. Disconnect module from compressor, install new unit. While you're in there clean the condenser coils with a vacuum and clean the fan and condensate pan. Reassemble, and you're chillin. Total time approx. 15 min.
Was this helpful?
Thank you for voting!
My wife broke the shelf support
1 person found this instruction helpful.
  • Hamid from Owasso, OK
  • Really Easy
  • Less than 15 mins
The new shelf support part fit perfectly. I needed no tools just slid it on the existing bracket. Super easy.
Was this helpful?
Thank you for voting!
A couple supports broke
2 of 4 people found this instruction helpful.
  • Michael from Cary, IL
  • Really Easy
  • Less than 15 mins
I simply slid off the broken supports, and slid the new ones on.
Was this helpful?
Thank you for voting!
Broken wheel on leveling roller
2 of 4 people found this instruction helpful.
  • Max from Jonesboro, AR
  • Really Easy
  • Less than 15 mins
  • Socket set
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 person found this instruction helpful.
  • Michael from Colorado Springs, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people found this instruction helpful.
  • Paul from Lowell, MI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
Condenser Fan Failure
2 of 5 people found this instruction helpful.
  • Al from Tonka Bay, MN
  • Easy
  • 30 - 60 mins
  • Socket set
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great !
Was this helpful?
Thank you for voting!
fan motor had gone bad
1 of 2 people found this instruction helpful.
  • william from whitwell, TN
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people found this instruction helpful.
  • William from Milford, MA
  • Easy
  • 30 - 60 mins
  • Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!
cooling fan quit
1 of 2 people found this instruction helpful.
  • George from Belhaven, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver
Ordered new fan motor on line took out old motor and replaced with new one
Was this helpful?
Thank you for voting!
Water tubing was accidentally broken from the back of the freezer.
1 of 2 people found this instruction helpful.
  • Lois from Thomasville, AL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together
Was this helpful?
Thank you for voting!
Two of the parts were broken so the shelf was laying on the drawers so neither could be used effectivly
1 of 2 people found this instruction helpful.
  • ROD from LINCOLN, NE
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pulled out the stud with a wire cutter and replaced it with the exact part you shipped in the kit.

The other 2 parts just slipped on the brackets

Nice thing is now I have extra parts for the other shelf.
Was this helpful?
Thank you for voting!
Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.
1 of 2 people found this instruction helpful.
  • Mike from Camas, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simply removed the old and replaced with the new part.
Was this helpful?
Thank you for voting!
Movers broke the icemaker water fill tube shoving my refrigerator through the front door.
1 of 2 people found this instruction helpful.
  • Christopher from Valley Village, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Was this helpful?
Thank you for voting!
All Instructions for the 1068670331
91 - 105 of 202