1067650521 Kenmore Refrigerator - Instructions

All Instructions for the 1067650521
91 - 105 of 226

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator was freezing up and not cooling fresh food compartment
2 of 3 people found this instruction helpful.
  • Greg from McLoud, OK
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sen t power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.
Was this helpful?
Thank you for voting!
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
3 of 6 people found this instruction helpful.
  • John from Greensboro, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
Was this helpful?
Thank you for voting!
The refridgerator will not run
2 of 3 people found this instruction helpful.
  • Victor from Colton, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.
Was this helpful?
Thank you for voting!
Freezer made lots of Ice and Refrigerator didn't cool
4 of 10 people found this instruction helpful.
  • Cecelia from Garden City, TX
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
The Defrost Timer is located in Refrigerator section (not the freezer) where your temperture guages are. Move panel and replace the non working Defrost Timer with the new one. It took my husband about 30-40 mins to fix. This was about 2 weeks ago and my Freezer and Refrigerator are working like new. I bought this Kenmore Reftigerator bran d new in 1996 and I lost the manuel to it. Thanks to my daughter who found the Defrost Timer on the Internet, I thought I was going to have to buy a new one. This was real easy to fix. The instructions that came with the part was easy to understand and very self explanatory. It also had very good diagrams to follow.
Was this helpful?
Thank you for voting!
Water dispenser drip when not being used.
1 person found this instruction helpful.
  • David from West Linn, OR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Wrench set
Unplug, turn off water supply, carefully remove lower back cardboard cover, unscrew old valve mount, lay towel down, disconnect the three water lines, modify provided “L” bracket by drilling a hole outboard of one of the slots to match/fit the wider original mount holes on the refrigerator’s bottom pan, screw top/short end of bracket to v alve, cut back the two clear lines about 1/2” for a “fresh” end, connect all three lines, position valve and secure with original screws (access is tight, used small 1/4” wrench), turn on water/check for leaks, install back lower cardboard, plug in and verify function.
Was this helpful?
Thank you for voting!
Water not entering icemaker
1 person found this instruction helpful.
  • Ruff from SELMA, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Initial problem was water not entering the icemaker. Replacing the valve assembly did not solve the problem. Further investigation revealed the inflow tube to he icemaker had frozen water in it. Cleaned the ice our and water flowed a bit but not enough to fill the tray. Still investigating the problem.
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people found this instruction helpful.
  • Paul from Lowell, MI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people found this instruction helpful.
  • Carolee from Spokane Valley, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Freezer Cold - Refrigerator Warm
3 of 7 people found this instruction helpful.
  • William from Fairfield Glade, TN
  • Easy
  • Less than 15 mins
  • Screw drivers
After searching online to diagnose the issue with my refrigerator being warm and the freezer being cold and not shutting off to defrost I decided to get the defrost timer kit. The kit arrived within 2 day. With the directions included, after unplugging the appliance for safety, I installed it relatively quickly with only a screwdriver . I then plugged it back in and it immediately went to defrost. I thought, wow I have it fixed. Well unbeknownst to me it still didn't cool in the fridge area. After doing more internet research I found a suggestion to unplug the fridge for 24 hours to unthaw ice that may be lodged between the freezer and fridge that is blocking the distribution of cold air into the fridge. After doing this, it now works like a charm.
Was this helpful?
Thank you for voting!
Replaced Crisper Pan shelf
1 person found this instruction helpful.
  • Joseph from Tucson, AR
  • Really Easy
  • Less than 15 mins
Removed old one and installed new one.
Was this helpful?
Thank you for voting!
Broken wheel on leveling roller
2 of 4 people found this instruction helpful.
  • Max from Jonesboro, AR
  • Really Easy
  • Less than 15 mins
  • Socket set
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 people found this instruction helpful.
  • MATTHEW from STOCKTON, CA
  • Really Easy
  • Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people found this instruction helpful.
  • Cathy from HOPATCONG, NJ
  • Very Easy
  • Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people found this instruction helpful.
  • Richard from North Easton, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people found this instruction helpful.
  • Douglas from Mesa, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
All Instructions for the 1067650521
91 - 105 of 226