- Home
- 1067650521
- Instructions
1067650521 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
cooling fan quit
1 of 2 people
found this instruction helpful.
-
George from Belhaven, NC
- Easy
- 30 - 60 mins
-
Nutdriver
Ordered new fan motor on line took out old motor and replaced with new one
Was this helpful?
Thank you for voting!
fan motor had gone bad
1 of 2 people
found this instruction helpful.
-
william from whitwell, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people
found this instruction helpful.
-
William from Milford, MA
- Easy
- 30 - 60 mins
-
Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!
Refrigerator compartment warm
1 of 2 people
found this instruction helpful.
-
alfonso from Fairfield, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
first confirm that freezer is cold. if is frozen solid it needs to be defrosted. take the freezer items out,take shelf out, bottom cover, 2 screws. then ice maker, 3 screws and unplug wires. then back panel 2 screws. In refrigerator compartment were the controllers are located, look under it you will see 1 hole, insert a flat end screw dr
... Read more
iver and turn clockwise till it stops. this action will turn on your defroster, also the compressor will stop. is the heater melting the ice? if so soak up water and clean tray, use hair dryer in drain hole to aid in the defrost, check tray under fridge and if its dry keep defrosting. it should take half an hour. now take the flat head screw driver and turn the defrost timer clock wise out of defrost mode a quarter turn or so. the compressor should come back on, soon after the fan in the freezer compartment should also come on. this steps lets you no that the defrost heater works, fan works and drain hole is clear. if its defrosted place parts back in the reverse order. if not defrosted replace heater or mother board. in refrigerator compartment were the dials are located their are 2 screws, one on the left and the other on the right side take them out, the cover will drop down, you will find wiring schematics you will need them to install defrost timer. is timer making ticking sound? if no replace timer. new timer will be different from original so follow instructions that come with it. timer is above were the hole is located. the plastic hold downs will break when you try to take them off, unplug fridge, lift timer out and remove from wire harness. the new timer has a black wire that slips over either 1 or 2 depending on color of wire on the wire harness. check schematics. some silicone adhesive will keep unit in place, ad some into the plastic shaft prior to installation, plug wire harness return wiring instruction along with new one inside of cover, plug in fridge, turn defrost timer clock wise with flat head screw driver making sure that you hold timer from above so it wont move. did compressor come on?. put all paper work inside of cover before installing cover
Read less
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people
found this instruction helpful.
-
James from Howell, MI
- Easy
- 30 - 60 mins
-
Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people
found this instruction helpful.
-
Jeremy from State College, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl
... Read more
aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Read less
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people
found this instruction helpful.
-
Cecelia from Beaver Dam, WI
- Easy
- 15 - 30 mins
-
Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
Broken wheel under fridge
0 of 1 people
found this instruction helpful.
-
Ted from Magnolia, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)
Was this helpful?
Thank you for voting!
took out old switch, replaced with new one from parts select.
0 of 1 people
found this instruction helpful.
-
Jo Anne from Easley, SC
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out icemaker,it had been letting in too much water, foynd switch was not working anymore, ordered new one from PartSelect, got it in a few days,took icemaker out put new switch in & it is working like new. I was amazed I could still get parts for a 28 year old whirlpool. And with the help I got from PartSelect,I am really thankful. J
... Read more
oAnne, Easley, S.C.
Read less
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people
found this instruction helpful.
-
William from Schwenksville, PA
- Easy
- Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!
light bulb went out in my oven
2 of 7 people
found this instruction helpful.
-
Janet from Ada, MI
- Really Easy
- Less than 15 mins
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people
found this instruction helpful.
-
Shirley from Las Vegas, NV
- Really Easy
- Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people
found this instruction helpful.
-
peggy ann from forest city, NC
- Really Easy
- Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
light would work intermitently
0 of 1 people
found this instruction helpful.
-
Gregory from middle island, NY
- Easy
- Less than 15 mins
-
Screw drivers
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this helpful?
Thank you for voting!