- Home
- 1067650521
- Instructions
1067650521 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker would not make ice
5 of 7 people
found this instruction helpful.
-
Jack from The Woodlands, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I Have a Sub Zero refrigerator, but has a Wirlpool ice maker. The ice maker has been repaired 4 times in 2009!!! A complete new ice maker one time! The repair man repaced the double outlet valve three times in 4 months. Then they had to but in a in line water filter. This solved the problem for six months. I thought the water filt
... Read more
er would last at lease a year. It will now be changed every six months. For some reason I get minor amounts of dirt,in my water. If a small speck gets to the double outlet valve it causes it to "weep" and the tube that fills the ice tray freezes up. Since I have watched so many times as my ice maker was repaired, it was easy to diconnect the faulty valve with 1/4 inch wrench and the water filter. Replace with the new valve and water filter. Make sure the connections are tite. Turn the water back on and in 24 hours you have ice.
Read less
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people
found this instruction helpful.
-
Dave from Manchester Center, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this helpful?
Thank you for voting!
The water in the door dispenser would run for several seconds and then start clunking. This resulted in no more water flow.
5 of 7 people
found this instruction helpful.
-
Richard from Novi, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I guessed that the water dispenser solenoid was getting weak.
A quick web search led me to PartSelect's website where it was so easy to pull up my refrigerator model with diagrams. I ordered the valve kit, and in 5 days it was in my hands.
Installation was literally 10 minutes. It took longer than that to vacuum all the du ... Read more st from under and in back of my refrigerator !
A quick web search led me to PartSelect's website where it was so easy to pull up my refrigerator model with diagrams. I ordered the valve kit, and in 5 days it was in my hands.
Installation was literally 10 minutes. It took longer than that to vacuum all the du ... Read more st from under and in back of my refrigerator !
Read less
Was this helpful?
Thank you for voting!
Light in my refrigerator didn't work.
5 of 7 people
found this instruction helpful.
-
Joseph from Byron Center, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m
... Read more
e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Read less
Was this helpful?
Thank you for voting!
Refrigerator light would not turn on.
5 of 8 people
found this instruction helpful.
-
Suzanne from STERLING HTS, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom.
... Read more
The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Read less
Was this helpful?
Thank you for voting!
Dispensed water w/ funny looking particles
10 of 23 people
found this instruction helpful.
-
MARGARITA from TAMPA, FL
- A Bit Difficult
- 1- 2 hours
-
Wrench (Adjustable), Wrench set
First the small screws you sent did not fit.I had to cut and mend the old ones (2) to use them.I did purchase a connecting valve tha I used to connect the part of tubing (my name for it) from old one to new one.I was surprides it is working fine.Not bad for a nurse!
Was this helpful?
Thank you for voting!
Compressor making excessive noise
5 of 9 people
found this instruction helpful.
-
chester from Tampa, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled
... Read more
the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people
found this instruction helpful.
-
Winston A from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people
found this instruction helpful.
-
Jane from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80..
... Read more
.would have been at least $100 to have a repair person come to the house!
Read less
Was this helpful?
Thank you for voting!
no ice
5 of 9 people
found this instruction helpful.
-
Thomas from Va. Beach, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
directions very well written, easy to follow, no problems
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
the light socket broke apart
4 of 7 people
found this instruction helpful.
-
Elyse from Skokie, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this helpful?
Thank you for voting!
Refrigerator quit cooling and the freezer wasn't freezing anything
4 of 7 people
found this instruction helpful.
-
Tonya from Grand Prairie, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new f
... Read more
an. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.
Read less
Was this helpful?
Thank you for voting!
Divider front of fridge hot to touch Condenser fan not working
3 of 4 people
found this instruction helpful.
-
John from Holden, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people
found this instruction helpful.
-
David from Hemet, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t
... Read more
he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Read less
Was this helpful?
Thank you for voting!