1065004 Kenmore Refrigerator - Instructions

All Instructions for the 1065004
121 - 135 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The original was broken.
1 person found this instruction helpful.
  • Shawn from ROSWELL, GA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Take it apart, replace with the new one, put it back together. So simple even a democrat girl could do it.
Was this helpful?
Thank you for voting!
Freezer Cold at 2 Degrees, Refrigerator Warm at 48 Degrees
1 person found this instruction helpful.
  • Lenny from Boca Raton, FL
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..
Was this helpful?
Thank you for voting!
The light switch broke when an item fell on to the switch
1 person found this instruction helpful.
  • Valerie from York, PA
  • Really Easy
  • 15 - 30 mins
Following a you tube video, I followed the instructions. However, the old switch did not come out as easy as the video showed. They showed inserting the putty knife at the bottom of the switch to pop out the switch. However, in my refrigerator, the flex tab was at the top. After I inserted the putty knife at the top of the switch it c ame out easily. I removed the broken switch and inserted the new switch with no further issues.
Was this helpful?
Thank you for voting!
No problems
1 person found this instruction helpful.
  • Richard from PORT JERVIS, NY
  • Very Easy
  • Less than 15 mins
Just plugged it in
Was this helpful?
Thank you for voting!
Ice would not dispense out of the ice bucket
1 person found this instruction helpful.
  • Rob from MIAMI BEACH, FL
  • Very Easy
  • Less than 15 mins
SUPER EASY. I pulled out the ice bucket and confirmed the motor ran and the axel turned - however the coupling was missing. Ordered the coupling - pulled out the ice bucket, screwed on by hand with minimum effort, put ice bucket back and ice started coming out the door. It took less than 5 minutes and no tools required.
Was this helpful?
Thank you for voting!
No cold
1 person found this instruction helpful.
  • Jacqueline from LEXINGTON PK, MD
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people found this instruction helpful.
  • Cathy from HOPATCONG, NJ
  • Very Easy
  • Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
Ice dispenser not working.
2 of 4 people found this instruction helpful.
  • Kerby from BEVERLEY HILLS, FL
  • Really Easy
  • Less than 15 mins
  • Pliers
All I did was unscrew the stripped one and screw the new part on. You just have to get it started unscrewing first ( remember that it's backwards! ).
Was this helpful?
Thank you for voting!
Plugged it in.
1 person found this instruction helpful.
  • Adam from GLOVERSVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this helpful?
Thank you for voting!
Freezer occasionally had a temperature alarm.Clicking noise also.
1 person found this instruction helpful.
  • Barry from FORD CITY, PA
  • Really Easy
  • Less than 15 mins
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this helpful?
Thank you for voting!
freezer and refrigerator compartments not cold enough
1 person found this instruction helpful.
  • Michael from Colorado Springs, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this helpful?
Thank you for voting!
Ice maker nod dispensing cubed ice.
1 person found this instruction helpful.
  • Charles from Dearborn Heights, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver
Disassembled freezer icemaker rear panel and replaced defective part.
Was this helpful?
Thank you for voting!
Difficulty removing old switch.
1 person found this instruction helpful.
  • Ronald from HUNTINGTN BCH, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this helpful?
Thank you for voting!
freezer would not freeze
1 person found this instruction helpful.
  • Michael from HELENDALE, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thic k. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this helpful?
Thank you for voting!
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
1 person found this instruction helpful.
  • John from AUBURN, CA
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this helpful?
Thank you for voting!
All Instructions for the 1065004
121 - 135 of 326