1065004 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Bin Auger Drum was broken.
3 of 4 people
found this instruction helpful.
-
Charles from Liberty hill, TX
- Really Easy
- 15 - 30 mins
-
Socket set, Wrench (Adjustable)
First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being car
... Read more
eful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)
Read less
Was this helpful?
Thank you for voting!
Random clicking noise
3 of 4 people
found this instruction helpful.
-
Mark from SAN DIEGO, CA
- Very Easy
- 15 - 30 mins
-
Nutdriver
The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..
Other Parts Used:
Was this helpful?
Thank you for voting!
Inlet valve was broken at the water line connection
3 of 4 people
found this instruction helpful.
-
James from VANCEBURG, KY
- Very Easy
- 15 - 30 mins
-
Nutdriver
Changed inlet valve
Was this helpful?
Thank you for voting!
fan motor needed replacing
2 of 2 people
found this instruction helpful.
-
Joe from ALBANY, GA
- Very Easy
- 15 - 30 mins
-
Screw drivers
System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.
Was this helpful?
Thank you for voting!
Ice deflector had broken.
2 of 2 people
found this instruction helpful.
-
Thomas from JACKSONVILLE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed ice tray and unbolted front cover. Removed broken piece and snapped new ice deflector in place. Reinstalled front cover and put ice tray back into freezer. Cycled crushed ice, works great!
Was this helpful?
Thank you for voting!
Loud banging after using water dispenser
2 of 2 people
found this instruction helpful.
-
Matthew from RANDOLPH, NJ
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Followed the extremely helpful video on the web site. It was easy to remove, replace, and install the new part, following their video. Saved time and money, and I didn’t lose anymore of my hair!
Was this helpful?
Thank you for voting!
Ice maker stopped producing ice.
2 of 2 people
found this instruction helpful.
-
Warren from PALMER LAKE, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the old ice maker by taking out three screws. Unplugged the electrical connection to the old ice maker. Replaced the old ice maker with the new one. Reconnected the electrical, replaced the screws, and reset the new ice maker. The replacement part has been working perfectly. This was an extremely easy replacement job!
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people
found this instruction helpful.
-
dorotea from staten island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
ordered a new ice maker, new refrigerator did not come with one.
2 of 2 people
found this instruction helpful.
-
Scott from ROCHESTER, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I watched the video that was included with my on line order, it was helpful, although different model shown . I would say it was not difficult to install, the enclosed instructions were a bit confusing.
Was this helpful?
Thank you for voting!
Ice maker leaking
3 of 5 people
found this instruction helpful.
-
Clifford from WASHINGTON, DC
- Really Easy
- 30 - 60 mins
-
Nutdriver
Unplugged freezer turned off water removed 3 nut screws Unplugged old ice maker installed new ice maker
Was this helpful?
Thank you for voting!
There was no water in the icemaker tray to freeze into ice cubes
3 of 5 people
found this instruction helpful.
-
Thomas from GRANT, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Took off the rear cardboard cover, unscrewed the old valve, checked to see if there was enough tubing to fit if I cut the tubing. removed the 2 electric connectors, Cut the tubing 3, installed the 2 electric plugs, inserted the 3 tubes, mounted the new valve, replaced the cardboard cover. I checked for leaks, and very soon heard the valve
... Read more
filling the icemaker tray, and soon, Ice cubes again.
Read less
Was this helpful?
Thank you for voting!
Freezer ice maker not dispensing ice.
2 of 2 people
found this instruction helpful.
-
Johnny from MORGAN CITY, LA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Ordered Ice Bin Auger and changed with no problem. Found how to change on YouTube and followed video.
Was this helpful?
Thank you for voting!