1065004 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced door gasket and hinge closers on Refrigerator door.
2 of 2 people
found this instruction helpful.
-
David E from EL SOBRANTE, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.
Was this helpful?
Thank you for voting!
OLDER Ice Maker on the fritz
6 of 14 people
found this instruction helpful.
-
Eric S from Boca Raton, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench set
Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric
Was this helpful?
Thank you for voting!
install ice maker with all parts for refridgerator with no ice cube hardware on it.
2 of 2 people
found this instruction helpful.
-
Vincent from THE VILLAGES, FL
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I followed the directions and it worked.
Was this helpful?
Thank you for voting!
ice maker
2 of 2 people
found this instruction helpful.
-
Ann from MC CUNE, KS
- Really Easy
- 30 - 60 mins
My husband is an appliance man and he did the work.
Was this helpful?
Thank you for voting!
No ice making.
2 of 3 people
found this instruction helpful.
-
Joseph from EDEN, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took old ice maker out; put in new ice maker.
Was this helpful?
Thank you for voting!
freezer (later fridge too) wouldn't stay cold~
2 of 3 people
found this instruction helpful.
-
David from MARYLAND HTS, MO
- Very Easy
- 30 - 60 mins
-
Nutdriver
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and acce
... Read more
ss panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Read less
Was this helpful?
Thank you for voting!
Auger blades separated from hub.
3 of 6 people
found this instruction helpful.
-
Randolph from Derby, KS
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove a
... Read more
nything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.
Read less
Was this helpful?
Thank you for voting!
The door switch was broken so the interior light would not come on.
2 of 3 people
found this instruction helpful.
-
Catherine from BROOMALL, PA
- Easy
- Less than 15 mins
-
Screw drivers
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and th
... Read more
e new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Read less
Was this helpful?
Thank you for voting!
Freezer drawer light switch failure.
2 of 3 people
found this instruction helpful.
-
HARRY from FSTRVL TRVOSE, PA
- Really Easy
- Less than 15 mins
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into
... Read more
trim. Plug refrigerator into wall socket.
Read less
Was this helpful?
Thank you for voting!
none
2 of 3 people
found this instruction helpful.
-
Joseph from BONITA SPGS, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
install ice maker 2 screws wire harness pluged in done
Was this helpful?
Thank you for voting!
Light switch on door broke
3 of 6 people
found this instruction helpful.
-
Donna from Oro Valley, AZ
- Really Easy
- Less than 15 mins
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Light out.
1 person
found this instruction helpful.
-
Carlton from CHICAGO, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped out the old switch and replaced it with the one dying
Was this helpful?
Thank you for voting!
3 screws
1 person
found this instruction helpful.
-
Michael from SALINA, KS
- Very Easy
- Less than 15 mins
-
Nutdriver
Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.
Was this helpful?
Thank you for voting!