Electrolux Fridge Parts

This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is an easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.

This OEM refrigerator filter is for french door and side-by-side door types and is located in the back, top-right of your appliance. By absorbing heavy metals, pharmaceuticals, pesticides, chlorine, and much more, this filter provides delicious and healthy drinking water. This filter measures 2 inches deep, 9 inches high, 2 inches wide, and weighs 0.9 lbs. The installation is quick and easy with a push and twist feature. Don't forget to run water through the dispenser for about three minutes or 1.5 gallons to prepare the filter before use. For best performance replace this filter every six months.

This manufacturer-approved Refrigerator Door Shelf Bin is made of white plastic and is easy to install. It is used to hold heavier items in the fridge, and you'll be able to visually see if the part is broken. This particular shelf attaches to the fridge door and is designed for the UPPER shelf. You can check if this model is right for your appliance by checking your user manual and model number. This is a simple repair that requires only that you snap the old part out of place and snap the new one into place.

The PurePour water filter is compatible with Frigidaire, Frigidaire Gallery and Professional side-by-side and French Door refrigerators with PurePour ice and water filtration. This genuine Frigidaire replacement water filter fits Frigidaire refrigerators which feature a cylindrical filter housing mounted on the refrigerator's ceiling. With the FPPWFU01 filter, you can relax knowing your drinking water is safe, clear and healthy.

The crisper pan, also known as a vegetable drawer, is used to store your vegetables and fruit at a humidity level that will help keep them fresh longer. The pan is clear and made of plastic. This is a genuine OEM part.

This part releases water from the supply line when it's activated. NOTE: This part may appear different than the original, but is an authorized manufacturer replacement.

This carbon-activated air filter is designed for refrigerators equipped with Pure Air Ultra II filtration systems. It helps maintain a fresh interior environment by absorbing strong odors from foods like onions, garlic, seafood, and overripe produce. By reducing these smells, the filter also helps preserve the taste and quality of your ice. Installation is quick and tool-free: simply remove the plastic wrap from the new filter, open the housing cover inside the refrigerator, take out the old filter, insert the new one, and close the cover. Depending on your refrigerator model, you may need to reset the filter indicator. This OEM

This mullion hinge pin is designed to secure the mullion in place within compatible refrigerator models, allowing it to pivot smoothly as the doors open and close. Measuring approximately 1.5 inches by 1.25 inches by 0.85 inches, it helps maintain proper separation between the refrigerator and freezer compartments, supporting consistent internal temperatures. A damaged or loose hinge pin can lead to temperature fluctuations, frost buildup, and difficulty operating the doors. Replacement involves removing the mullion cover, detaching the old pin, inserting the new one into the hinge assembly, and reattaching the cover. Some models may require two pins—one at the top and one at the bottom. Each pin is sold individually.

This genuine PureSource Ultra water filter will fit most Frigidaire french door and side by side refrigerators. You will find this filter located in the back, top right of the appliance. It is white in color and the filter has a polypropylene plastic housing and extruded carbon block filter media. Certified by NSF/ANSI to reduce contaminants that may be in your household water supply by 99.8 percent. The operating temperature for this filter is 33-100 degrees Fahrenheit, the flow rate is 0.5 GPM, the working pressure is 30-100 PSI, and it has a micron rating of 1. This filter should be replaced every six months or when the indicator lights up red. Installation is quick and easy. Push on the end face of the older filter to allow it to release. Remove and discard the old filter. Slide the new filter into the housing and press it down until it locks into place. Be sure to run water through the dispenser for about three minutes to prime the filter before use. Discard this water or use it to water plants. Do not forget to reset the indicator by pressing it down for 3-10 seconds. Review the use and care guide before you install for more detailed instructions.

This NSF-Certified OEM filter is white in color with a plastic housing and extruded carbon filter media. It measures 2.3-Inches deep, 9.1-Inches high and 2.3-Inches wide. It fits certain Frigidaire side-by-side models after 2009 that use a water filter located in the back, top right. Filters all dispensed drinking water and the water used for making ice. It minimizes chlorine flavor and smell and cuts down on common contaminants by 99 percent. You will need to replace the filter every six months or when the light indicates. To install the new filter slide it into the housing and push until it locks in place. Press the indicator button for ten seconds to reset after replacing.