This kit includes 1 shock absorber and 2 mounting pins.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
LG, Kenmore.
Part# 383EER3001S replaces these:
AP4998813
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bearing seal out causing bearings to get wet and very noisy
Watched a short video to figure out to remove panels. After panels were off I removed as much as I could from the inside of the machine. This was not completely necessary however for an extra half hour it made inspection, cleanup and removal of tub housing out the front of the machine much easier. Once out, I split the two halves of the outer basin and sprayed the spider shaft with penetrating oil. Using a brass drift I did have to get a bit aggressive to drive spider shaft out, then I used a heavy metal punch to hammer out the bearings. For those who may not know using brass or a soft metal will keep from damaging reusable parts. At this point it was cleanup time, with dish soap I scrubbed the two halves of the outer basin and the wash basin itself then used emery cloth on the bearing casing and spider shaft. I am a firm believer if u take the time to cleanup properly things go back together much easier. At this point I began to reassemble, replacing tub bearings and seal, the wash basin then putting the two halves of the outer basin back together. I strongly recommend replacing gasket for the halves of the outer basin, for as much as it takes to get there it is money well spent to up the chances of a leak free system. Now with the wash tub back together it was time to reset the tub and hook everything back up. I skipped a lot of steps but if a person pays attention, takes pictures if they have to, even numbers lines with a sharpie it is a very easy repair. Very easy but very time consuming. I am DIY’er, in all I spent about ten hours over two days to do this job. Thus being said I am very particular spent a lot of time cleaning, scrubbing looking at as many wear points and checking for rubbed wires. Hope this helps someone out there, definitely not a strong writer or like doing it. Oh one other thing, I ordered the shocks on the bottom side of wash tub just because I guess not thinking they were bad just thinking I could help tune it up. Was surprised to find the old ones were completely shot, was glad I ordered new ones. After repairs, noise is gone and machine is quiet again. Thank you, your website is very easy to find parts and order.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Christopher Karch
December 19, 2017
My washer is moving during spin cycle. My research tells me to change the k610 shock absorber. Are there 3 total? Are there any other parts needed, i.E. Springs?
For model number WM2101HW
Hello Christopher, Thank you for your inquiry. Yes, there are 3 shocks in this model. We usually recommend checking the springs as well. Hope this helps!
10 people found this helpful.
Was this helpful?
Thank you for voting!
Ashley
February 27, 2018
My washer is smoking from inside the tub. It still runs through all the cycles but once its finished and i open the door, smokes comes out. What could be causing this?
For model number WM2450HRA
Hi Ashley,
Thank you for your question. I think it would be a good idea to check both of those parts. I would also suggest checking the motor, belt, and pulley as well. The burning rubber smell is usually a sign that the motor or belt is wearing down but it could also mean that there is a problem with your bearing. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
June 15, 2022
Does this shock absorber fit my washing machine model WM2240CW
For model number WM2240CW
Hello Robert, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS3522317. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3522315
Manufacturer Part Number: 383EER3001S