GE/GE_Thumb/00009937i03.gif
See part 121 in the diagram
Replacing your General Electric Range Trim Ring - 6 Inch play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

Trim Ring - 6 Inch

$16.89   Special Order

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS244475
Manufacturer Part Number WB31X5013
Manufactured by GE
Product Description

Trim Ring - 6 Inch Specifications

This 6 inch high rise burner trim ring is intended for use with detached style low rise tilt lock surface mount burners on ranges.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Range, Microwave Oven Combo, Cooktop.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WB31X5013 replaces these:
AP2028085, 5, 340525, WB31X0056, WB31X5008, WB31X5013A, WB31X5013B, WB31X5013DS, WB31X5013R, WB31X5015, WB31X56
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Part Videos

Replacing your General Electric Range Trim Ring - 6 Inch

Replacing your General Electric Range Trim Ring - 6 Inch play video
Customer Repair Stories
 Average Repair Rating: 4.6 / 5.0, 35 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Needed to replace Drip Pans and Trim Rings for old stove
Repair was simple (just lift off the old and put on the new). What was pleasantly surprising was how quickly I received the parts (amazing)!

Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct parts.
Other Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch
  • Cynthia from Tampa, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
38 of 44 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners Heated Irratically
1. Pulled out drawer
2. Vacuumed dust, etc. under stove
3. Reached under stove to rear and pulled plug
4. Pulled the stove out away from wall so I could get to back
5. Removed 5 screws that retained the back of the control panel
6. One by one, I removed each wire from an old control and pushed it onto the same pin on the new control - did same for all 4 burner controls
7. Removed the knobs
8. Removed 2 screws from the front panel for each old control and removed the old controls
9. Pushed each of the new controls into place on the panel and reused screws to secure them in place
10. Cut the long control stems using 2 pliers per instructions to match length of old controls.
11. Used knob adapters provided to mate the old knobs to the new control stems
12. Plugged the stove in and tested the burners
13. Unplugged and replace the panel back with original screws
14. Moved stove back into place
15. The right front burner was the one most used, so I replaced the connector for that burner.
16. That connector came with instructions that I followed - cut the wires to the old connector, splice the wires to the new connector wires using supplied wire nuts and shrink tubing.
17. Plugged the stove back in
18. Replaced drawer - job complete - stove like new
Other Parts Used:
Porcelain Drip Bowl - 8" Porcelain Drip Pan - 6" Trim Ring - 8 Inch INFINITE HEAT SWITCH KIT Terminal Block
  • HOWARD from WATERBURY, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
14 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Drip bowls and Rings
Received the Drip bowls and Rings very quickly. Opened the box and then cut open the plastic wrap that the individual rings and drip bowls were in. Lifted the burner on the stove top, took out the old ring and drip bowl. Installed the shiny new drip bowl and ring, then lowered the stove top element back into place. I was able to replace all 4 of them within 5 minutes. Made the 30 year old stove look brand new.Thank you for perfect fit parts and fast delivery.
Other Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch
  • Joe from Oakley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners were 50 years old, yes 50. They still worked but were beginning to show the use that they have had over the years.
I did the repairs by first shutting down the power and then checking with a tic tester to make sure power was off. Removed one burner at a time by unscrewing the holding screw on the hinge and then removed the ceramic insulator cover and then disconnected the wiring. I drew a schematic for the 3 wire leads (240 volts). Unscrewed them and removed the burner. Cleaned stove top, put burner back in reverse order. Very easy project. Stove top looks as good as it did when it was new.
Other Parts Used:
Tilt-Lock Hinge-Mounted Surface Burner - 8" Tilt Lock Hinge Mounted Surface Burner Kit - 6"
  • Deborah from Streator, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowls WAY out of style
So this ancient stove we inherited when we bought our house had the drip bowls wrapped in tin foil. We've searched EVERY (not joking) store in our area for drip bowls that would fit it, but apparently Hotpoint wanted to make sure you could never do this - well, at least not easily. No one, not one store carries drip bowls to fit it. I finally searched online and partselect.com came up first on the list. I was amazed they had the right part! Better yet, ordering was beyond easy, and they came super quick. Popped in the parts in less than 2 minutes, and we're good to go - makes this old stove look new! (well, if this was the 80's, lol) When I clicked on the part it said which stoves it would fit, which was also very helpful. Thank goodness for Part Select! Otherwise we would've had to rewrap those disgusting old bowls... I'd recommend this site in a heartbeat!
Other Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch
  • Joanna from Fargo, ND
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front 6 inch and 8 inch burners gave up after 41 years.
It took about 20 min to flip the breaker off and remove the 2 hinge screws and disassemble the 3 wires on each burner and reattach same to new burners. All the hardware was included with the parts went together fast. Flip the breaker back on and everything works perfect.
Parts Select was the only place I could find replacement parts for such an old cooktop.
Thanks, Jerry
Other Parts Used:
Tilt-Lock Hinge-Mounted Surface Burner - 8" Tilt Lock Hinge Mounted Surface Burner Kit - 6"
  • Jerry from Hollywood, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
pans old and rusty and needed replacement
I had called GE for the part numbers from the 1970's GE range. Then entered the part number on this web site. The cost from GE for four reflector pans/rings would have been $130. The price I paid here was $60. Both prices included the shipping. I received the order in a few days from Fed Ex. Wrapped in original GE plastic.

Thank you so much.
Other Parts Used:
Drip Bowl - 6 Inch Drip Pan - 8 inch Trim Ring - 8 Inch
  • Judy from Bend, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed To Replace Drip Bowl
I just replaced them.
Other Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch Trim Ring - 8 Inch
  • DIANA from TINTON FALLS, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad switch plus a disintegrating element
Moved into a house built in 1976 about 7 years ago that came with an old but nice looking GE electric stove.
Stove worked well until about a year ago when the switch for the 8" element became erratic. Having been raised where DIYS was SOP I didn't even consider calling for help instead, armed with the stove model number, I went to the internet (How on earth did I ever survive before internet?) and found this site where I quickly found the exploded view of my stove, IDed the switch, ordered and received it within a day or so. Fantastic turn around time!

Now I've never ever worked on an electric stove so I was quite methodical in my approach.

First I read the instructions (you know, when all else fails…) that came with the new switch, then I pulled the stove out, unplugged it and removed the tin back that covers the switches. I drew a diagram of the old switch orientation and which wires attached to what. Then I disconnected the wires, removed the knob and the two screws hiding behind it that hold the switch to the stove.

Oops, the new switch was not identical to the old!!

First: I noticed was that the stem for the knob was longer BUT they proved break off notches so that it can be shortened.
Second: the stem on the old switch was a half round while the new stem was square. I tried the 'half round' knob on the square stem and it went on firmly. Nothing ventured nothing gained.
Third: the terminal orientation did not match. So armed with my diagram and the instructions I made sure I knew which terminal was which (they are labeled). Once assured I knew what went where (I made notes) I installed the new switch and attached the wires (following my notes).

Being an optimist I reinstalled the tin back, plugged the stove in and pushed it back into position before (with my legs, arms and fingers crossed) I tested the switch (which was not easy considering the position I was in). Lo and behold, no puff of smoke and…ta-da…everything worked as it should.

All in all, upon receiving the switch the whole thing took less than 30 minutes.

Recent.

Less than two weeks ago one of the 6" elements fell apart, still worked but lost the supports that rest on the trim ring. Back to the internet to ordered a new element and new trim rings (just for the cosmetics). Again great service, I think I received my order the second day.

Along with the element they also supply new screws plus the spring clips which hold the ceramic insulator together. There's only two wires to contend with so its easy to determine which is the left wire and which is the right. The old terminal screws were locked in pretty good so I used pliers to hold the terminal while loosening them. There's very little slack in the wires so it was a tad awkward reattaching them to the new element.
I did notice that the threaded hole on the new element seemed to be slightly larger than the old. I noticed this when I used the old screws, one would tighten, the other did not so I replaced with the screws they supplied (Duh!). Well I do have an excuse, the new screws were longer which I feared would prevent the insulator from 'closing'.
I probably spent the most time attaching the insulator. I found I needed to fiddle with position of the terminals before the two halves of the insulator would meet. I splayed the wires out slightly then cocked the wire ends slightly so that the wires would neatly leave the side of the insulator. I also adjusted the terminals and the bendable wire part on the element so that they were parallel to each other.

ANYBODY can do this
Other Parts Used:
Trim Ring - 8 Inch Tilt Lock Hinge Mounted Surface Element - 6"
  • John from Merriam Woods, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Small elements were losing heating power and large elements did not work.
I unplugged each element from the terminal it was plugged into and then plugged the new element in. I also replace the drip pans and trim rings while I was at it.
Other Parts Used:
Porcelain Drip Bowl - 8" Porcelain Drip Pan - 6" Trim Ring - 8 Inch Surface Element - 8 Inch - 2350W Surface Element - 6 Inch - 240V
  • Joseph from Guilford, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS244475
Manufacturer Part Number: WB31X5013
Brand
Model Number
Description
Hotpoint
107RC445F
Range - Hotpoint Range/Stove/Oven Model 107RC445F Parts
Hotpoint
107RC690H
Range - Hotpoint Range/Stove/Oven Model 107RC690H Parts
Hotpoint
107RH971E
Range - Hotpoint Range/Stove/Oven Model 107RH971E Parts
Hotpoint
107RH971F
Range - Hotpoint Range/Stove/Oven Model 107RH971F Parts
Hotpoint
107RHV755J
Range - Hotpoint Range/Stove/Oven Model 107RHV755J Parts
General Electric
107RHV786J
Range
General Electric
108RB545-G
Range - GE Range/Stove/Oven Model 108RB545-G (108RB545G, 108RB545 G) Parts
Kenmore
20131
Range - Kenmore Range/Stove/Oven Model 20131 (1988) (20131(1988)) Parts
Kenmore
20221
Range - Kenmore Range/Stove/Oven Model 20221 (1988) (20221(1988)) Parts
Kenmore
20231
Range - Kenmore Range/Stove/Oven Model 20231(1988) Parts
Kenmore
20232
Range - Kenmore Range/Stove/Oven Model 20232(1988) Parts
Hotpoint
207RC669
Range - Hotpoint Range/Stove/Oven Model 207RC669 Parts
Hotpoint
207RCX549
Range - Hotpoint Range/Stove/Oven Model 207RCX549 Parts
Hotpoint
207RF755
Range - Hotpoint Range/Stove/Oven Model 207RF755 Parts
Hotpoint
207RH971F
Range - Hotpoint Range/Stove/Oven Model 207RH971F Parts
Hotpoint
207RHV786J
Range - Hotpoint Range/Stove/Oven Model 207RHV786J Parts
Hotpoint
207RHW872F
Range - Hotpoint Range/Stove/Oven Model 207RHW872F Parts
Kenmore
22104
Range - Kenmore Range/Stove/Oven Model 22104 (1988) (22104(1988)) Parts
Hotpoint
407RF45
Range - Hotpoint Range/Stove/Oven Model 407RF45 Parts
Hotpoint
407RF50
Range - Hotpoint Range/Stove/Oven Model 407RF50 Parts
Kenmore
99121-8
Range - Kenmore Range/Stove/Oven Model 99121-8(1988) (991218(1988), 99121 8(1988)) Parts
Kenmore
99138
Range - Kenmore Range/Stove/Oven Model 99138 (1988) (99138(1988)) Parts
Kenmore
99141
Range - Kenmore Range/Stove/Oven Model 99141 (1988) (99141(1988)) Parts
Kenmore
99148
Range - Kenmore Range/Stove/Oven Model 99148 (1988) (99148(1988)) Parts
Kenmore
99151
Range - Kenmore Range/Stove/Oven Model 99151 (1988) (99151(1988)) Parts
Kenmore
99158
Range - Kenmore Range/Stove/Oven Model 99158 (1988) (99158(1988)) Parts
Kenmore
99211
Range - Kenmore Range/Stove/Oven Model 99211 (1988) (99211(1988)) Parts
Kenmore
99221
Range - Kenmore Range/Stove/Oven Model 99221 (1988) (99221(1988)) Parts
Kenmore
99228
Range - Kenmore Range/Stove/Oven Model 99228 (1988) (99228(1988)) Parts
Kenmore
99241
Range - Kenmore Range/Stove/Oven Model 99241 (1988) (99241(1988)) Parts

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service