Troubleshooting
This part fixes the following symptoms:
Touchpad does not respond
This part works with the following products:
Range.
This part works with the following products:
Frigidaire.
Part# 316419821 replaces these:
AP4433205
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
James B - October 15, 2023
Verified Purchase
Worked great
Perfect replacement...needed control panel
Lori Ann M - October 18, 2018
Verified Purchase
Part perfect should tell people that order part it fits on that you need it cause your old face is not usable cause it is stuck on does not peel off cause sticky
Stove is back up working ordered first part said no overlay included. Didn't know what over lay was no picture. That would be helpful. Cause cant use you old one because it is peel and stick
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Touch Screen Overlay
I was actually replacing an EOC and it did not state anywhere that I might need this. In the end I did, the new board is not compatible with the old overlay and I had no idea so intended to re-use the old one. I had to wait for the new one and it worked fine. The EOC had actually been damaged by a power surge and it was obvious it was bad. I was actually hoping that this would resolve a temperature drift issue but it did not.
Other Parts Used:
-
Kenneth from LIBERTY, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven control board went bad
ordered control board from PARTSELECT if you need it fast over night it remove rear of back guard with NUTDRIVER 4 phylips screws hold the control board in place it helps if you have a phone to take pictures to see where the wires go when you connect them to the new board the overlay is not to hard you have to make sure to start at one end and get the end lined up use your fingers to feel the edge of the control board at one end put overlay in place and gently lay it in place and start laying it down slowly making sure it is going strieght once your at the other end and its down i used a soft cloth to press it down across the face and happy to say the syove is working once again
Other Parts Used:
-
Robert from SCRANTON, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electronic Control Board Oven not heating timely or at all.
Watched You Tube 3 times. Removed the stove back covers top and bottom.
Ordered the new electronic control board and overlay.
Took picture of existing control board and connections.
Viewed parts select online schematic of the stove, make and model.
Ordered the new black overlay, did not want to take time to try to save old black overly.
Parts arrived.
Re-watched You Tube.
Installed the new electronic control board and included electronic filter as per You Tube.
Tested the oven.
Works like new.
Saved $ 200 to $ 300.
Great fun.
Hero to my wife !
Ordered the new electronic control board and overlay.
Took picture of existing control board and connections.
Viewed parts select online schematic of the stove, make and model.
Ordered the new black overlay, did not want to take time to try to save old black overly.
Parts arrived.
Re-watched You Tube.
Installed the new electronic control board and included electronic filter as per You Tube.
Tested the oven.
Works like new.
Saved $ 200 to $ 300.
Great fun.
Hero to my wife !
Other Parts Used:
-
Charles from AURORA, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Patricia
September 23, 2019
Can't set the clock, show's a code SD
For model number LGEF3045KFE
Hi Patricia, thank you for your question. That code actually stands for Store Demo. What you have to do is unplug the appliance for about 45 seconds. Then when you plug it back in press and hold the Oven Cook Time button until the SD disappears. I hope that helps. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Ryan
February 26, 2018
Does this have the adhesive already on it.
Hi Ryan, Thank you for the question. The overlay is Peel and Stick with the adhesive backing already on it. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Bernie
December 19, 2019
Does oven electronic controller board ps9494055 normally correct code 11 and ore 12
For model number lgef3045kfk
Hello Bernie, thank you for your question. Yes, that would fix that error code. We would recommend replacing the overlay as well. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Alex
November 26, 2021
Error message F14. Continuous beeping
For model number LGEF3045KFB
Hello Alex, Thank you for the question. The F14 Error code indicates the user interface panel cable is missing or disconnected. We suggest checking the cables and wiring to make sure nothing is damaged or loose. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
September 14, 2023
I ant see if the touch panel has the ribbon wire in the picture. My current panel seems to have a issue with the pizza button and that is giving me the F11 code all the other buttons beep when I press them.
For model number CGEF3040PFA
Hello Jim, thank you for your question! F11 error is a shorted key error. It means when a key on the keypad has been detected as pressed in for a long time, the F11 error is reported and all oven commands are terminated. First, simply press the cancel key to clear the code. The error may have been caused by just holding down a key too long by mistake. Try to reset the electronics by killing power to it at the breaker/fuse panel on your home for one full minute, then restore power. If the error persists, you will need to replace the overlay, part number PS2364031, and electronic control board, part number PS9494055. We hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Amanda
20 days ago
My digital screen for my oven won't work at all. It won't cut on . It won't light up. There are no signs of any burns or wires coming loose. Nothing the control board looks great. I have unplugged the range, turned the breaker off. Turned back on after waiting 20 mins or longer . Plugged range back in and still nothing on the display. What should I do now. Do I need to buy both the control board and the overlay. Any advice would be great. Thank you
For model number LGEF3045KFC
Hello Amanda, thank you for your question. We suggest replacing the Overlay PS2364031 first. If that does not correct the issue, you may need to replace the Electric Control Board.PS9494055. You can test each one with a multimeter. We have a video on how to use the multimeter. We hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
Dawn
February 13, 2020
Oven has a mind of its own. Temperature keeps climbing way above what i've set it for and burns everything. Yesterday it was up to 550 (when i set it for 350) and then it started beeping with a f10 error code. Nothing cleared the code but unplugging the unit. What could be going on here?
For model number LGEF3045KFB
Hello Dawn, thank you for your question. F10 indicates that the control detects a runaway temperature in the oven. If the oven is overheating, this can be caused by a stuck relay or contact on the oven electronic control board. If this fault code appears when the oven is at room temperature, then the failure points to a failed oven temperature sensor probe circuit or a bad electronic oven control board. If you are able to unplug the range and access the oven temperature sensor, you can check the resistance of this component with a volt/ohm meter. At room temperature, most Frigidaire oven temperature sensor probes will measure about 1100 ohms at room temperature. If your probe measures 2500 ohms or higher, then a defective temperature sensor is causing this problem. If the sensor is okay, then I recommend reconnecting the sensor and checking the resistance through the wiring harness connection directly at the electronic oven control board (with the range still unplugged). The sensor is oven connected through violet wires on Frigidaire ranges. If the resistance is normal through the wires that plug into the control board, then it is likely that you will need to replace the control board. I hope this helps
Was this helpful?
Thank you for voting!
Doug
November 13, 2018
Can you use the old overlay on the new eoc
For model number LGEF3045KFK
Hello Doug, Thank you for the question. Yes, the old overlay will work on the new EOC. Hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Curtis
February 1, 2019
My oven will not heat up , i changed out the coil did not work. So do i need 20a or 20
For model number lgef3045kfk
Hello Curtis, Thank you for the question. I woudl first suggest testing the oven sensor probe. PartSelect Number: PS11731755. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If the sensor is good you will need to replace the Electronic Oven Control Board, PartSelect Number: PS9494055. Thank you for your inquiry, good luck with this repair!
Was this helpful?
Thank you for voting!
Related Parts:
Gigi
March 11, 2019
Do you need to clean adhesive off the control panel when replacing the oven control pad?Adhesive remains on the panel after peeling off the pad.
thank you
Hello Gigi, Thank you for the question. Yes, I woudl suggest cleaning the old Adhesive off in order to reinstall it properly. Good luck with the repair!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2364031
Manufacturer Part Number: 316419821
Manufacturer Part Number: 316419821
Brand
Model Number
Description