Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Kenmore Washer Front Load Washer Bellow - Gray
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Rod P - February 12, 2024
Verified Purchase
Part came on time as expected.
Part was easy to install with the help of the great video repair link they sent. Very impressed with my first ever dealing with part select
★★★★★
★★★★★
Guy T - January 11, 2024
Verified Purchase
Easy replacement
Good product but problem remain
★★★★★
★★★★★
Robin R - January 30, 2023
Verified Purchase
Great instructional video
Steve did an excellent, detailed job of explaining the repair, and that made it much easier. The right part came quickly.
★★★★★
★★★★★
Brad P - September 2, 2022
Verified Purchase
Easy repair
Received the part real fast. Watched the partSelect video how to replace it. No problems at all. Will order again.
★★★★★
★★★★★
Dianne B - July 13, 2022
Verified Purchase
Perfect fit
Perfect fit and although it took some time to do the installation it was easy to do when following along to the instruction video. Very happy!
★★★★★
★★★★★
Valerie S - June 29, 2022
Verified Purchase
Came quickly and works well.
My daughters were able to install the bellows easily except for one part which required stronger hands to complete. Fortunately we had a friend at the house who was able to do it for us. It has worked perfectly ever since.
★★★★★
★★★★★
Rodney G - March 27, 2022
Verified Purchase
Fast and efficient delivery - videos are remarkable
The part came with all the necessary parts needed to make the swap. Appreciated the how to video to ensure that I did the job correctly the 1st time. Will certainly be using partselect.ca for any other parts needed.
★★★★★
★★★★★
Kelley P - October 17, 2020
Verified Purchase
Way less scary than it looked
This hardest part was taking the front off. Once that was done, it was no problem, I was surprised that there were no clamps with it as mine were rusty and hard to move. They just a couple of bent wires. We managed but in would have been good to know.
★★★★★
★★★★★
Randall K - September 29, 2020
Verified Purchase
very good part.when in 40 min.No more leeks
when in 40min had no trouble putting in. the outer spring i found to be better to put in from the bottom.
★★★★★
★★★★★
Chris W - July 15, 2020
Verified Purchase
Easy Order and Installation!
Parts came correct and fast. Video made installation a breeze. My wife was ready to spend a pile of money on a new washer but thanks to Part Select, I was able to find the right part to fix our washer and cancel her shopping plans! Thanks again!
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 2.7 / 5.0, 16 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water leak from bottom of door.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
Other Parts Used:
Marty from Belfair, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
200 of 223 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Epic Z is only three years old but started to leak at the bottom of the washer door for no obvious reason. Before replacing the bellow, I suggest you make sure the door latch is not loose and also make sure the star driver screws that secure the glass in the door are all snug (do not overtighten)
Since most people do not replace bellows for a living, I have great instructions for you to follow. I found the entire repair manual on the web.Just follow the repair instructions as written. Two other suggestions, use a very small amount of liquid diswasher soap to lubricate the bellow when fitting it over the washer drum assembly, makes life a lot easier. Second, get a second pair of hands to help you hold the bellow in place as you mount it or you will find yourself "chasing your tail". Bellow replacement and tightening the door and latch fixed the problem. Mom was happy :)...PS the buying experience from PartSelect , part delivery, speed was perfect!
Other Parts Used:
Robert from Charlotte, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
53 of 56 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bellow was cut on the bottom, leaked.
The top panel was removed, right side pulls out, left side has a lint drawer that pulls out exposing a phillips head screw. The bottom panel is removed by taking three screws out of the bottom, then the panel pulls down. Remove the additional screws (4) holding the door panel on. Loosen the band (phillipshead screw) holding the bellow on and pull the bellow off the channel. It also pulls off the door opening channel. Pull the new piece over the channels, tighten the band and reverse the removal procedure.
Other Parts Used:
Richard from Mount Pocono, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
33 of 47 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking at door
once i figure out how to take off front panel it went quite smoothly also my wife gave me a hand putting the bellows on,her fingers were smaller so it was alittle easier for her
Remove outer retaining ring by pulling spring clip located at bottom of the seal. Push the bellows into the tub. Loosen the inner retaining ring clip (located on the left, facing the front of the machine) with a phillips screwdriver and guide the ring out. Remove the old bellows. Put in the new part with the tab on top and the drain holes on the bottom. Reinstall the rings. Kind of tedious but not complicated.
Other Parts Used:
Christopher from Myrtle Beach, SC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
19 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced leaking bellows
I followed the description on this site, my machine was slightly different, but the basic procedure was the same. The tip to apply a small amount of the liquid soap to the bellows was useful to ease installation. Make sure the holes in the bottom of the bellows align with the drain in the bottom of the washer. The portion of the bellows that attaches to the main body via the adjustable clamp can be done by a single person with two hands. The portion that attaches to the front panel with the spring-wire band is a four hand job. Position the bellows, attach / position the wire-band with the spring portion on the bottom. Starting at the top get your helper to hold it in position, using needle nose pliers stretch the last bit of the wire-band into final position.
Other Parts Used:
thomas from santa cruz, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
16 of 18 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bellow was torn at the door causing water to leak
I would recommend to remove the front loader door first. Then remove the clamp that holds the front of the bellow to the washer, Remove the top panel and then the front panel. Remove the band that holds the back of the bellow to the washer. Reverse the process to install the bellow. It helps to apply a little soapy water to make it easy to put the bellow on the track for both the front and back. It also helps to have four hands. Hope you have a friend or significant other.
Other Parts Used:
Rich from Los Altos, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
11 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door seal had gone bad leaked
Looked how the old one came off and revearsed the process. Ordered the part, it was shipped right away and recieved it in three working days. Normal shipping too. Very pleased with the handling of my order.
Other Parts Used:
Roy from Summerville, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
11 of 18 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaked from front bellows. (Door gasket)
Easier if you block up front feet on 2x4 blocks. remove bottom front panel. Remove detergent dispenser tray. Remove top front panel. On door remove large round retainer clamp to bellows. (Pop off with screwdriver.) Remove door. Remove inner bellows clamp. Use phillips screwdriver to loosen it. If the input water filler hose is in the way, pull it out, but don't forget to put it back on or a flood will ensue!! Replace by doing everything in reverse order.
Other Parts Used:
Joseph from EAST SYRACUSE, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking around door & inside tub
Watched your video worked great just like video showed
Other Parts Used:
Terry from MCCOOK, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
17 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cassie
April 2, 2018
Hello, my washer is leaking from what appears the front and water is dripping down into the drawer below. We only notice this with heavier loads like towels. Is it likely the bellow is the concern given that it doesn't leak with lighter loads? Thanks for your advice!
For model number WFW8300SW04
Hello Cassie, thank you for your question. If there is any leak from the front of the door the bellow is the culprit. It may only happen on larger or heavier loads now, but will probably progress to leaking all the time. I would suggest replacing the Bellow - Gray WPW10111435. Good luck with your repair!
22 people found this helpful.
Was this helpful?
Thank you for voting!
Bill
December 3, 2017
Our machine is dripping water on the inside. When you remove the bottom panel there is a cement counterweight and the water is dripping down the back of the counter weight into the base of the machine. Is this the part that will solve that leak?
For model number WFW8300SW00
Hi Bill,
Thank you for your question. You would likely have to try and figure out where your leak is coming from. It could be coming from your bellow but it could also be coming from the tun gasket. I would suggest letting your appliance dry out a bit. Maybe open it up so that you can see the inside. Take a little bit of water, pour it over your bellow and see if there is a leak. If there is not, pour some of the water into your tub and spin it around for a minute or so. See if there is a leak. I hope that helps. Good luck with your repair.
My washer boot is black with mold. I saw the replacement part number: Wpw10111435; but i didn't see the number that is listed on my washer (8540903). The closest was 8540954. The serial number of mine is: Hlt1677748 (about 11 years old. I bought the floor model when i moved here.) please let me know if this indeed is the appropriate boot for my old washer. Many thanks. Kimme
For model number WFW8300SW00
Hi Kimme,
Thank you for contacting us. Based on the model number you provided, the bellow you have referenced in your question is the correct part for your appliance. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Alexander Pries
January 12, 2018
Hi there, we have a Kenmore front loading washer that leaks a small amount of water into the metal frame at the bottom. I removed the kickplate and noticed that the water is dripping from the backside of the bottom concrete counterweight. I also noticed that the water only seems to drip during the high spin portion of the washing cycle. During normal agitation, there seems to be no leakage or maybe just holdover drips from the high spin phase. Is replacement of the door bellow the most likely solution or could there be another faulty part? I ask because i had previously replaced the door bellow about six months ago and have noticed no leaks until recently. Thank you!
For model number Kenmore 110.47511702
Hello Alexander, Thank you for your inquiry. You can pull the bellow out and check for any rips or tears. Check the drain hoses and tub to pump hose as well. The other parts that could cause this issue are the drain pump, the water inlet valve and the tub assembly. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Charles
January 30, 2023
The bellows on the front load washing machine is leaking. This is a stacked washer & dryer combo unit. Do I need to remove the dryer on top the washer to remove panels and access the bellows for replacement?
For model number WFW8300SW02
Hello Charles, Thank you for writing. Yes, the dryer will need to be removed to access the panels to remove then and replace the Bellow. We hope this information helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Kally
January 31, 2019
Hi i was wondering which gasket seal for the door replaces my model washing machine. Thank you
For model number MHWZ400TQ01
Hello Kally, thank you for your question! PartSelect Number PS11748353 is the correct part for your model. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Alix
August 26, 2019
Hi, I have the Whirlpool WFW8300SW00, is this bellow compatible with my washing machine? Thanks.
For model number WFW8300SW00
Hi Alix,
Thank you for your question. Yes, this would be the correct bellow for your washer. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Miriam
December 12, 2019
My washer is leaking from the bottom of the door and I'm assuming this is the part I would need to fix it? Will it fit my model. Serial # hlu429267.
For model number 11047532602
Hello Miriam, thank you for the question. With leaking at the door, in most cases the Front Load Washer Bellow - Gray, PartSelect Number PS11748353 will need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jason
November 21, 2021
Hi, my washer leaks and the drips seem to come from the bottom from behind the front panel. I believe it's the boot but I was wondering why it leaks more when I run an empty load. When I do a clean the washer cycle and there are no clothes it leaks a large volume of water. Could this still be the boot leaking?
For model number WFW8300SW02
Hello Jason, thank you for your question. We have researched the model you have provided, and we would suggest the Washer Bellow, part number PS11748353 or the Water level Switch, part number PS11749322. To test the water level switch, unplug the washer and remove the switch. You can test it with a multimeter. Set your multimeter to the lowest ohms of resistance and test your switch. If it does not read any continuity, then your switch is indeed faulty. We hope this helps.
My washer leaks when on normal on any mode. It leaks in the front corners.And into the drawer. I have to put rags on the front corner to soak up water. I'm thinking that it is the seal of the washer? Could that be it.
For model number WFW8400TW02
Hi Chelsea, Thank you for the question. I suggest replacing or checking for damage on the Bellow, PartSelect Number PS11748353. It may have just come lose. At times it can get pinched or split and will need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11748353
Manufacturer Part Number: WPW10111435
