Product Description
Door Gasket - gray Specifications
This dishwasher door gasket is gray in color and is used for some belt driven dishwashers. This gasket is made of rubber and is eighty-nine and three quarter inches long.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
Maytag, Jenn-Air, Kenmore, Kenmore.
Part# WP901403 replaces these:
AP6013599, 7-57036, 757036, 9-1403, 901403, Y757036
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Aletha T - October 20, 2022
Verified Purchase
Old machine, great part, works like new
I was delighted that this part for my very old dish washer was still available. It was easy to install and the machine and I are very happy. Thank you
Robert G - October 15, 2019
Verified Purchase
Dish washer door gasket
Fit perfectly but at high cost around $100.00 for a rubber gasket
Richard R - February 19, 2019
Verified Purchase
Straightforward repair - for two people
The part came with proper installation instructions and advised that it would take one person about two hours to complete the repair. We followed the instructions and had two people involved (the extra set of hands are very helpful at certain points; e.g. holding the instrument panel away from where the work was being done). With the extra set of hands, the repair took 20 to 25 minutes. The machine is back in operation and the new seal seems to make it run a little quieter than when the old seal was in place.
Heather L - October 11, 2018
Verified Purchase
Worked as expected
Arrived quickly and fit my 20 year old dishwasher perfectly
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 12 reviews.
What's this?
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
replace door seal
Remove old seal by pulling out tabs one at a time.
To install new seal, I had to remove the front control panel and door panel to access the back side of all of the slots that the new seal tabs go into. Using needlenose pliers i pulled each tab individually until they were locked into place.
Replace door and control panel.
To install new seal, I had to remove the front control panel and door panel to access the back side of all of the slots that the new seal tabs go into. Using needlenose pliers i pulled each tab individually until they were locked into place.
Replace door and control panel.
Other Parts Used:
-
Jeffrey from Wilmington, DE
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
36 of 41 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket was leaking
Removed the gasket by pulling it's tabs out of the metal slots in the door. This was accomplished by accessing the inside of the door.
Then I realized that I had to dissassemble the side and front panel of the door to install the new gasket. The reason is you have to pull the tabs through the metal slots in the door from the front side. I used needle nose pliers which worked well. Then I had to reassemble the front and sides of the door. No more leaks!! for now. Takes some time if you do it by yourself. Budget at least 2 hours.
Then I realized that I had to dissassemble the side and front panel of the door to install the new gasket. The reason is you have to pull the tabs through the metal slots in the door from the front side. I used needle nose pliers which worked well. Then I had to reassemble the front and sides of the door. No more leaks!! for now. Takes some time if you do it by yourself. Budget at least 2 hours.
Other Parts Used:
-
Mark from Bloomingdale, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
16 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door gasket leaking-door hard to lift due to broken spring
remove lower access panel to expose spring. remove broken spring with longnose pliers. with door closed install upper hook of spring with nylon bushing on door hinge. using longnose pliers pull down on spring to hook on lower braket.
Other Parts Used:
-
JEFFREY from La Mirada, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
13 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking around door
cleaned lime and calcium build up off of gasket
and it stopped the leak . yea . parts select was very helpful and said i could return the unused
gasket. . this is a good place to get parts.thanks larry
and it stopped the leak . yea . parts select was very helpful and said i could return the unused
gasket. . this is a good place to get parts.thanks larry
Other Parts Used:
-
Larry from Auburndale, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Leak Lower Left, Bottom Of Door
Removed the old gasket. It was easy to "pop out" the parts that held the gasket in place with a regular flat blade screwdriver. Becareful not to chip the porclien (sp). Any of the tabs that broke off I just pushed them through and can take them out if I ever need to remove the front of the door. Works fine and no leaks. Clean the area of the old gasket so the new gasket will have a good seal. End of story.
Other Parts Used:
-
Jerry from Mason City, IA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
7 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher was leaking through the door.
All I had to do was take apart the door by removing a few screws. Then ripped the old gasket off. I then lined all the tabs up to make sure it was going to fit and then started pulling them through with needle nose pliers. When the door was reassembled I checked the plastic piece where the gasket ends in the tub and found some loose screws that needed to be tightened. After that I ran a few cycles and it does not leak any more.
Other Parts Used:
-
Bradley from HEBER CITY, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the door gasket was leaking
Easy to change. Just pull firmly on old gasket, clean surface with soapy water. Align tabs on new gasket, push into place a tap firmly with handle of a screwdriver and taps pop into place. Was done in about 40 minutes.
Other Parts Used:
-
Thomas from Beecher, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water coming out of door bottom
Pull old gasket off (30 seconds), take panel screws out of front panel and control panel, carefully lower control panel push tabs thru holes from inside door, once all tabs in, push door closed and take pliers and pull tabs until they lock into place, put panel back together. not that difficult, my wife and I had it back in working order in approx 30min.
Other Parts Used:
-
Danny from Barboursville, WV
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original gasket was worn away
I opened the door and pulled the old gasket out using a flathead screwdriver to pry up the difficult to remove areas. I cleaned the area with a damp cloth and place the new gasket in the slots. The entire process including the cleaning took no more than 10 minutes. It was so easy. By the way, I had the part in my hands 2 days after ordering it. I am very impressed with the service.
Other Parts Used:
-
Donna from Branchville, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door gasket cracked
Removed the front of the door by removing 2 screws in each side.
Remove 2 screws on each side holding control panel
Removed old gasket by pulling it out, and installed new gasket. Used needlenose pliers to pull tabs securely into slots.
Remove 2 screws on each side holding control panel
Removed old gasket by pulling it out, and installed new gasket. Used needlenose pliers to pull tabs securely into slots.
Other Parts Used:
-
Reavis from Asheville, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Louise
December 14, 2017
How do i install the gasket
For model number WP901403
Hi Louise,
Thank you for your question. You would loosen the screws between your doors front panel and inner panel. That way it will be easier for your to remove the old gasket. Once you have that done, start from either bottom corner and slip the tabs between your panels. Then tighten the screws and you are good to go. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11746825
Manufacturer Part Number: WP901403
Manufacturer Part Number: WP901403
Brand
Model Number
Description