Average Repair Rating: 4.3 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Turntable did not turn when anything on top
Turn off the circuit breaker to the microwave. Remove the 4 black wood screws that secure the microwave to the cabinet. Pull the microwave all the way out and set it on something that leaves you access to the middle access panel on the bottom. Remove the access panel on the bottom that has one screw. Unhook the 2 cables to the motor remembering which color goes where. Remove the 2 screws for the motor and replace the motor. Finish up in reverse...
Other Parts Used:
Javin from Waltham, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
10 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable motor was making noise
Unscrewed and dropped the bottom panel of the Advantium on its rear hinge, disconnected the light and the motor, removed the motor screws, and replaced the motor. Very simple. However, not related to the Advantium or the motor, trim had been applied to the bottom of the wall cabinets after installation of the Advantium. This trim prevented the lowering of the panel (and future removal of the whole oven), so I had to chisel and file and repaint the trim to get it out of the way.
Other Parts Used:
Allan from LOUISVILLE, KY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
MOTOR STILL DOES NOT TURN
PER YOUR INSTRUCTION
Other Parts Used:
Robert P. from DEDHAM, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
August 8, 2018
The answer to turntable not turning explains how to replace motor... good instruction. can i replace motor without removing oven? also, initial response also suggests checking "coupler" for stripped gears... where is coupler? part of motor assembly? ready to buy part from you... excellent service.
For model number psa1200rww01
Hi Bob,
Thank you for your question. You will not have to remove the microwave from the cabinet to perform this repair. The coupler is usually the piece in the middle of the microwave floor that the glass tray sits on and is sometimes referred to as a turntable shaft. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
JOSEPH
September 24, 2019
Nearly 20 year old....microwave is working when we open the door, without setting a time also makes noise when the tray rotates
For model number JVM1660
Hello Joseph thank you for writing .
It sounds like a problem with the drive motor. We would need your complete model number to try to find you the right motor. Hope this helps. Contact us anytime.Part # PS237772 is similar to what you would need.
Will microwave still heat even if the turntable is defective. My turntable does not turn but does not heat food. Should a new turntable motor fix my problem?
For model number PSA1201RSS01
Hello Sally, Thank you for the question. Normally it would still heat but not evenly. We suggest checking the Diode Cable, PartSelect Number PS239148. Most cases it will show burn marks if defective. We hope this helps.
Turntable will turn extremely slow with weight on glass or metal tray (like 2 out of 10 tries) but mainly won't turn at all. I checked the turntable guide with rollers and there are no flat spots on rollers. I can also spin the turntable drive coupler so that isn't locked up.
For model number ZSC1001KSS01
Hi Dwight,
Thank you for your question. Then you may need to replace your motor. I would suggest just taking off your coupler and making sure the teeth on the inside of the shaft are not worn down as well. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1020855
Manufacturer Part Number: WB26X10193