WFW9400SW03 Whirlpool Washer - Instructions

We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

Followed internet instructions

Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.

Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together

Removed screws around door couple around hinge

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.

Easily. 4 Screws. 2 Clamps.

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

Lineup slots and snap in place. So easy even a caveman can do it.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.

Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve

NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.