WFW9400ST02 Whirlpool Washer - Instructions

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

A real novice at dyi. Found what the error code meant in the manual and google searched it online. Found Youtube video on repair and was successful in getting the washer to work a few times before the error code returned. Decided to replace the inlet valve and on your site took the advice of a previous user and also changed the flowmeter. Could not have been a better experience. Easy to find the correct parts for my model and got great tips...plus your shipping was excellent. Thanks!

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Removed the 3 bolts attaching top of washer. Disconnected hoses from the inlet value and flow meter, also very careful to remove the wire connections. Removed Water inlet valve (this requires the star screw driver). Did find it best to connect the inlet valve and flow meter before reattaching the inlet valve, as that sits under the lip, it is just a bit of a tight fit to get the hose reconnected between the two. Then reconnected the flow meter hose to the dispensing box, reattached the hoses and ran a cycle no f20 issues, as a note, an f20 has to do with a restriction in the flow of water not with pressure so not sure if it was the inlet valve or flow meter clogging up or both.

My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you

It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.

Disconnected power. Turned of the water supply. Removed/disconnected the water lines from the washer. Removed the top by removing three screws. Disconnected the wires/connectors from the valve assembly. Disconnected the water line from the valve assembly to the dispenser assembly. Removed the screw holding the valve assembly on. Installed the valve assembly and reversed the above procedure.

Disconected washer, disconected water lines, Removed top cover. Removed screw holding valve, disconnected 2 connectors for valve put everything back together

Removed top of washer and replaced flow meter.

repair was a cake-walk with the video there to help.Thanx

Greatest difficulty was positioning machine to get at rear. Disconnected inlet hoses. Removed rear 3 screws to remove cabinet top. Removed rear holding screw to inlet valve. Removed two electrical connections to inlet valve. Disconnected inlet valve from interior hose. Reversed process to install new inlet valve.