SHP78CM2N/22 Bosch Dishwasher - Instructions

All Instructions for the SHP78CM2N/22
16 - 26 of 26

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this
6 of 9 people found this instruction helpful.
  • Claire from ALPINE, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.
Was this helpful?
Thank you for voting!
Pump and heater failure!
5 of 7 people found this instruction helpful.
  • Neil from CHESTER, WV
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers, Wrench (Adjustable)
Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!
Was this helpful?
Thank you for voting!
Water leaking and high pitch noise mid way through operation.
5 of 7 people found this instruction helpful.
  • Lowell from SALEM, OR
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Mistakenly opened covers for the drain pump. Had to put those covers back in place.
Heater and pump installed easily with a bit of careful maneuvering the plugs and plug housing from the exterior. Pump installed in place easily. Clamp fit perfectly.
Was this helpful?
Thank you for voting!
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
4 of 5 people found this instruction helpful.
  • Ronald from WASHINGTON, MI
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Was this helpful?
Thank you for voting!
The old basket didn’t fit in the new lower rack
4 of 5 people found this instruction helpful.
  • Pat from Wichita, KS
  • Very Easy
  • 30 - 60 mins
just placed the basket in the rack
Was this helpful?
Thank you for voting!
Over the years the filter became too clogged with embedded particles
4 of 5 people found this instruction helpful.
  • Jim from EDINA, MN
  • Really Easy
  • Less than 15 mins
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this helpful?
Thank you for voting!
We accidentally damaged the upper spray arm
3 of 4 people found this instruction helpful.
  • Sheldon from ROCKAWAY, NJ
  • Really Easy
  • Less than 15 mins
Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes
Was this helpful?
Thank you for voting!
Water leakage from the dishwasher; unknown source.
2 of 2 people found this instruction helpful.
  • Bill from Seattle, WA
  • Really Easy
  • Less than 15 mins
Followed the video on your site and it was an easy install with no more leakage.
Was this helpful?
Thank you for voting!
Spray arm plug into water source became worn out and difficult to engage
2 of 2 people found this instruction helpful.
  • David from Sequim, WA
  • Really Easy
  • Less than 15 mins
The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.
Was this helpful?
Thank you for voting!
Chronic water leakage
2 of 3 people found this instruction helpful.
  • Callan from CHICAGO, IL
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.