RUD3000DB2 Roper Dishwasher - Instructions

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.

I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to yo ... Read more ur company for any suggestions, No reply.

The new lower rack came with wheels, but there were some other plastic parts I needed to move from the old rack to the new. No tools necessary! Use the old rack as a reference to make sure you put the wheels on the correct sides.

As described with instructions, removed original "bearing," installed replacement, removed original spring, installed replacement springs. Not difficult.

I USED A PLUMBER

I removed the three screws holding the motor on the housing. Then I took the two hoses off and from inside the washer I unscrewed the ring at the base of the wand that holds the housing in place and removed it. I then replaced the impeller and seals and reversed the process to put it back together. Cost me 26.00 for parts and shipping. I ... Read more couldnt imagine what anyone else would have charged. I will do business with PartsSelect again in the future.

Simply bend the lid so hinges slip out of sockets, and repeat to put the lid in the new basket.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

After getting the pump and motor off of the dishwasher, I used a screwdriver and small hammer to break the impeller off of the motor shaft. The shaft was corroded and pitted real bad but this doesn't matter because the shaft of the impeller actually goes through the seal. I removed the old seal and replaced it, slipped the new impeller ... Read more back on the motor shaft and put the pump and motor back on the dishwasher. Our local repair man told us it couldn't be repaired and we needed a new dishwasher. I had the parts from Part Select in 2 days. The parts were less than $35 dollars and repair very simple. The person on your comment section on how to fix it that said to break the old impeller off of the shaft made the job very simple.

had to replace the insides of a leaky pump

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the ... Read more motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer ... Read more clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. La ... Read more te Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.

I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!