PLES389ECH Frigidaire Range - Instructions

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Third time was a charm. Following PartSelect repair percentages I first replaced the oven sensor which did not fix problem. Next I replaced the main terminal block and oven baking element. Again , this did not fix problem. Lasty I replaced the oven electronic clock/ timer and the oven started working properly.

watched a U-Tube video on this subject.....worked like aa charm!!

Turned off power to oven. Pulled control dial from each element control. Removed plactic nut from each control and removed panel. Marked all connectors to "duel element control" for easy placement on new control unit. Replaced panel and installed plactic nuts. Replaced oven lamps and reinstalled the glass bulb covers. Turned power back on and tested element control that was replaced. Tested oven lamps by opening oven door. Everything went well.

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

Found a YouTube video similar to the required repair. Took door off, disassembled the door, replaced the right hinge-spring assy, reassembled. Worked great. High quality replacement part from Part Select that was made in the USA.

I went to you-tube and found a video that told me how to remove and expose the hinge. That was all I needed. One stubborn screw was all the problem I had and it was replaced. Thank you for saving me lots of money!! It's working great and I would buy from Part Select again!

Replaced both springs. Follow instructions in owners manual on removing door. Spring assembly resides in door. Remove screws holding spring assembly in place, then the remaining screws holding the inside of door in place. Raising the side, slide out old spring then slide in the new one - do the same on the opposite side. Replace all the screws - starting with those that hold the spring assembly making sure the latches are straight. Put the door back on making sure to lock "spring locks" detailed in owners manual

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

The hinges had just wore out ofter several years of service. We took the Oven Door of, simply and took the hings off and ordered the new ones. VERY EASY TO DO. The shipping, my my goodness Ordered on Thursday noon time and received the items before 4 pm on Friday. I just can't get over how quickly You shipped this item. Thanks You, and I will use You again, should the need arise. H. Briden Culleoka, TN