NDE5800AYW Amana Dryer - Instructions

I took out 6 screws and replaced the heating element, changed wires and reinstalled

Remove screws to top of appliance lid and control panel paying close attention to location and type of screws. Lift back of top panel and lift off front top lid until it snaps up. Slide top panel to side and remove upper front panel screws from the inside of dryer one on left and one on right. Be careful to not let front door fall outward. Slide door panel up off of hooks at base of panel. Remove duct assembly by removing three screws located on the inside of the dryer at the front. Slide out and remove air duct assembly.

Removing the High Limit Thermal Fuse was straight forward. Didn't really understand the online instructions but performed a continuity test across terminals and there was no continuity, so I replaced.

Repare took 1-2 hours, next time will probably cut in half now that I know where to remove screws to access motors & fuses and dryer assemblies at base of dryer.

Propped the machine up in the front, removed the front panel, the door assembly, and the front drum support. Use a Sharpie to mark wire positions. This will help during re-assembly. To get the drum out, you first have to remove the belt from the motor pulley. Drum slides right out. You will need snap-ring pliers to remove the pulley from the idler arm. I also replaced the drive belt because it was cheap, and always a good idea to replace it when you are this far into the machine if it is a few years old. Re-assemble in the reverse order of disassembly. An easy fix for the average do-it-yourself person.

I used a large flat head screwdriver to lift top up, then located 2 screws in the top right and left hand side to remove front. Remove the three Phillip Head Screws that holds the assy in place slide out. Mine had 2 metal pieces with wires. I simply unplugged and took metal pieces and installed in the new assy. Remove excess lint put front back on lowered lid and done! 15-20 minutes

Removed the lower front cover. Unplugged two wires and removed two screws in element, slid element out, removed two contacts and attached them to th new element, slid element back in place, inserted two screws re-attached two wires.
Very easy!

Jumped out both limits and flame would still go out, grab the 2 plug gas valve solenoid and it would click and the flame glow coil would start back up. I ordered both solenoid valves and the flame would stay on longer but not like it used to. On time drying the flame should stay on all the way thru the cycle unless it got to hot and the cycling stat would take over. Ordered a cycling stat and now it heats like it used to. The clothes are hot now when they come out. If you jump out the limits and still the flame doesn't stay on like it used to, replace the gas valve solenoids and the cycling stat.

Terminal Block was cracked and dryer was not receiving enough voltage, causing the heating element not to heat. Here were the steps I took to fix the problem:
1. Turn off breaker to dryer from 240v outlet
2. Unplug dryer from 240v wall outlet.
3. On outside, rear of dryer, remove cover plate and the clamp that the power cord goes through with nut driver or phillips screwdriver and take picture or write down how the power cord wires go to the terminal block.
4. Use nut driver or phillips screwdriver to remove the power cord wires from terminal block and ground wire from dryer body.
5. On top front of dryer, use large slotted screwdriver or some other tool to push in on the two clips in order to lift the cover up on dryer.
6. Take picture or write down how wires are attached to terminal block.
7. Remove wires from terminal block with nut driver or phillips screwdriver.
8. Use nut driver to remove terminal block from washer and install the new terminal block.
9. Reinstall wires to new terminal block.
10. Close dryer cover.
11. Reinstall clamp onto power cord wires and reinstall wires to new terminal block and ground wire to washer body then put cover plate back on.
12. Plug in dryer then turn on breaker.
13. Start dryer to see if it heats now.

Removed the control panel disconnect the wires on the bad part and replaced with new. Extremely quick and easy less than 10 minutes. Part ordered on line and received within one day.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.

took frount off ,then filter, pulled drum out, then blower plate & spun impeller off. went back together easy ,except belt . that gave me a little problem but finally got it thanks

I removed the access panel on the lower front. Then I removed the front door panel (noting where the wires went; 1 for red, 2 for black, 3 for grey). Then I removed the 2 screws holding the top down and lifted it up. Then I reached underneath the drum and took the belt off the tensioner. Then I removed the front drum panel with the lint filter, guides, and front felt seal. Then I took out the drum. Then I replaced the roller and post (with bracket). The old post was worn, so it was a good thing I got the new post (thanks to someone else's reccomendation). Then I put it all back together. It was surprizingly easy. I just wish these parts weren't so dad gum expensive. I paid $20 for one roller and post. I wish I could have also replaced the felt seals ($17 each), the other roller (another $8) and the sliders and felt pads ($20 per side). And a new belt. By then, you might as well buy a new dryer!

I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.

This was as easy as it can get. Took out old filter and replaced it with the new filter, which had a better design than the old part. Everything went great with our order. I'm putting your site on my favorites list, so in case I need another applicance part I you will just be a click away.

Installed new starter switch but it turns out that was not the problem. After checking the wiring diagram I tested the door switch and found that it was faulty. I jumped across it behind the control panel and now the dryer works fine.I'll replace the door switch later. If you do has I did remember that the dryer will then run with the door open and is dangerous. My mistake was I did not check the old starter switch with the ohm meter right off, silly me.