NDE5800AYW Amana Dryer - Instructions

Changed, got in aimed wrong direction-best to take a digital photo before you disassemble. Overtightened bolt and nut in assembly, it seized. Attempted to drill/grind it off, should have removed motor. Drill skipped up into motor windings. Could have replaced dryer, decided not, fixed by ordering motor, mount, nut and bolt and new belt idler. Reassembly was a snap till the gremlins hit again and I lost one of the drum glides. After a trip across town, I reassembled and it was good to go. Disassembly, use a screw driver to pry up the top, use the nut driver to remove upper front left and right screws, lift front forward and off bottom hooks. You have to release the wiring harness, it has four connectors. Use a sharpy marker and write the wire colors next to the plug-ins connectors you pull gently off and set the door aside. The second wires are two wires for the inner assembly which again need to be marked for color and then pulled loose. Pull them through the plastic hold down so they're out of the way. Use nut driver to remove four screws from inner drum holder, pry gently off dryer blower. Reaching around both sides of the blower housing find the belt tensioner, pull it to the right, push the belt out of it. Lift the drum out, up slightly over the back rollers. Set aside. Use the nut driver to remove the screws into the base holding the motor mount down, now lift the motor/blower assembly forward and pull gently loose from the dryer vent pipe. Set it up where you can work on it. Using the nut driver, take the screws off the blower housing, use a vise grip to secure the motor and use a 7/8 inch turning counter clockwise to remove the turbine. Use the nut driver to remove the screws holding the turbine housing in place, pop the motor clips off. Pull the motor off and remove the nut and bolt of the belt idler assembly using a wrench on the back and a socket wrench on the other side. Reverse order to reassemble, when tightening the idler arm tighten it to where you feel it stop but not any further. Put the belt around the drum again, get it in the previous location on the drum, feel around the drum to make sure belt isn't twisted, bring belt in from the back between the idler wheel and the vent pipe in a loop (Make sure the belt is behind the tension spring rather than in front), Tip the idler arm upward, use the other hand to slide the belt loop up over the motor pulley. One final note is this being a Maytag you might write these direction on the inside of the front panel for next time.

I removed 3 screws to open panel, removed defective switch, replaced with new switch. Reistalled panel, tested machine. Saved myself $100.00 service call charge plus having to wait for 2 weeks to have repair done. Priceless..........

I went to RepairClinic.com & FixYa.com for some great advice. I searched the internet for the parts. PartSelect.com was the most inexpensive. Delivery was good. Using the repairman's manual I found on the internet I followed the steps to remove each panel, in order. The wiring was the most bothersome, but okay to resolve; write it down and pull it off! I don't think the rollers, in the back, were bad. The tension idler was extremely worn. I tightened the tension idler bracket at the base. I did need to use an O-Ring Spreader to get all the rollers off and on. Although there were more panels to remove than older models, it was easier! Wrap the belt around the drum before reinstalling. The belt will loop around the drive & tensioner relatively easy. Replace the rubber seal around the drum & replace all the panels. Things are quieter now than I can remember in a long time.

watched video for Each Part

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

removed the front panel and the drum panel cover.replaced the guides and the felt pads and re-assembled.

Unable to find a repair manual or accurate diagram, I forged ahead and removed the top and front panels of the dryer. It took two tries to figure out how to thread the belt (nine of my ten thumbs kept getting in the way!), but after a coffee break, the job came together, and I've taken the clothesline down!

Unlike the other stories I read (and the video posted on the site), my unit had a lower maintenance panel on the front face which required quite a different disassembly. Once I took off the lower panel, there were screws at the bottom of the top panel. Once removed, the top front panel came out and exposed the necessary interior components. In order to get the drum out, I took out the screws holding the front of the top on and wiggled the drum out. From there I removed the belt and offending idler lever, put in the new ones and hooked the spring back up. Reverse procedure to assemble and the problem is completely gone. I even found and removed an unexpected hair band from the front skid plate. Pretty doable if you're willing to spend the time.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

Of course the lint filter is removed and cleaned every load, so I simpy removed the ld one and inserted the new one. No "installation" as such was required, we simply started using the new filter.

Removed back cover of console,using screwdriver and nut driver. Removed old switch by squeezing the end tabs and pulling switch out. Removed wires on switch with pliers. Placed wires on new switch using pliers. Snapped new switch back in place. Replaced back cover to console with screwdriver and nut driver.

remove old intstall new lint screen 10 seconds. your product was shipped fast!!!!!!!!!!!! i thought i would have to search this item out for days before a reinstallation was made. thanks for your fast professional service.

I asked the Gas Co. if they can come out and relight the pilot to my dryer... (which is common for gas dryers) He tested the equipment and told me that the thermostat was the problem. Most places was looking for around $160 for parts and labor. Well, I saved around 130, as I just simply replaced the thermostat. DONE DEAL!

Remove bottom panel from dryer. disconnect wires off of Limit switch. Unscrew 2 screws, remove old switch. Reverse to install. Important, if limit goes bad you need to replace cycling thermostat or chances are the limit will go out again. (Limit on back wall of dryer). The cycling thermostat is right under the lint screen. Remove 3 wires. Remove 2 screws, remove switch. Reverse to install new cycling thermostat. Toatl cost of 2 parts used 16 dollars and change. Thanks

After removing the lower access panel, I observed the drum and belt and saw it turning freely. The support rollers in the back turned freely and were in good condition as well. At odd intervals the unit made a humming or grinding noise, and i decided to check the blower wheel (the other rotating part in the system). I found that the central hub of the wheel (which is made of a nylon like plastic) had sheared off from the wheel itself. I ordered a new part and started to remove the old wheel. **NOTE** many of the stories I read described how this part would have a reverse thread, it did not and that cost me an extra 30 minutes to figure out (the new part had arrows showing the correct direction to put on and remove - the original didn't). Once everything was cleaned and reassembled, I started the dryer again, but got no heat. I had previously replaced the heating element, so I thought my wiring was wrong. That wasn't the problem, but a hint from this site about checking the incoming wiring was the solution, my ground wire had come off the terminal in the back of the dryer and I wasn't getting the volatge across the element that it required. With the ground wire back in place, everything worked fine.