MVW7232HW0 Maytag Washer - Instructions

The repair went really well. And it was the right part and now we can have light in our fridge.
Thank you!
Your help and fast shipping really made a difference. I will always shop for my parts with you guys. Thank you for having things no store has. It saves alit of money all around.
Thank you again.

Prepare:
Before you start turn off the hot and cold water supply. Then remove the supply lines from the back of the washer. You may want a bucket to catch any remaining water in the supply lines.

Replace water inlet valve:
First, remove screws from upper back plate to release the control panel and the washer top.
... Read more />
Second, slide washer top to the front of the washer about 1/2 - 1 inch. This will allow you to raise the washer top.

Third, from underneath the washer top release the control panel by disengaging the locking clips near the back of the control panel.

Fourth, lay the top back in to the forward position and hinge the control panel from back to front. This will release the control panel.

Fifth, Disengage the wire harness for the control non. And remove the control panel completely.

Sixth, remove the wiring harness from the water inlet valve located on the left hand side, the. Remove the screws holding the valve in place.

Seventh, Install new valve, reconnect all of the wiring harnesses, reconnect the control Bob wire harness, and reinstall the control panel. It should click into place just as it came out.

Eighth, Slide the washer top back into place. Reinstall the back plate and screws.

Finish:
Finally reinstall the supply lines and turn on the water.

If you take the back off the machine, it's a lot easier to detach the control bridge. Saved a lot of time and did not need to stretch your fingers

Turn off water and remove inlet hoses
Remove of control Tower
Remove control tower and unplug from rest of washer
Remove water inlet valve and install new valve
Reverse operations

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Untwisted it and slipped the new one in quick and easily in less than a minute

Removed Back and top of digit front. removed water intake valve part order new part replacing was a breeze

It was really easy after watching the videio. I removed a single screw and took the agitator out, You could see how worn the center of the part was. The part that it went onto had a lot of rust built up on it, I used naval jelly and a wire brush to clean it. then put the new agitator on. It has been working well ever since. What's c ... Read more razy is two repair men told me to
throw out the washer because the repair would be equivalent to buying a new one! NOT TRUE ---- Total cost $115.00. Received it really quickly. Thanks so much!

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. ... Read more The hose clip could then be tightened without deforming the hose. Worked great with no leaks.

It easily installed with a twist lock removal and installation. 2 minute fix.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Ordered the parts and followed You Tube DYI clip. This 3YOMaytag top loading washer has had a motherboard replaced and now this. It all works fine for now, I cannot imagine what the appliance tech would have charged. Maytag is not what it used to be.

I used needle nose pliers to remove the broken piece of the latch from the lid lock and removed the round broken latch assembly from the lid by twisting counter clockwise and removing it from the round inset hole on the underside of the lid.

I then took the replacement latch assembly, inserted it flush in the hole and twiste ... Read more d it clockwise until it snapped into position. It took less than a minute to fix. The latch is very thin, made of plastic, so I bought two, to have an extra as a backup.

after watching a video i ordered the part. removed the old part and installed the new wash plate using a socket and ratchet.
now washer works like new

I removed the cap and then undid the bolt. The bolt was difficult to remove I guess because it was I there so long and is a critical part. Once I had the bolt out I used a strap to get under the plate to pry up. Once it was off I checked the drive hub kit and found that it didn’t need to be replaced. I pit the new wash plate in place a ... Read more nd used a rubber mallet to help seat it once I knew the teeth were lined up. The bolt went back in easily and I replaced the cap!