MHWE450WR01 Maytag Washer - Instructions

Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.

I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

At first I thought it was the door lock so I replace it. I had the same problem. So I ordered the electronic control unit and that fixed the problem. It is very easy to replace. First remove the 3 screws that hold the top in place and slide it back about an inch to remove. The electronic control unit is right on top. It slides toward the ... Read more back of the washer to remove. There is a tab on the end that holds it in place. There are several connectors that have to be unplugged from the old unit and then attached to the new unit. Just pay attention where they go.

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Took old one off and put the new one on. Was very easy. Hardest part was disconnecting hose clamps, which was still easy

took front panel off. Pump is right there easy to work on. Used pliers to take 2 hose clamps off. Used star screw driver to take 2 screws off of pump and removed old pump. The Assemblely goes the same way but the drain hose coming off the tube is not very easy to get back on. Hose is flimsey and the stem, on the end of the drain pump isnt ... Read more long enough to keep hose on while tring to slide hose clamp back on.

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out ... Read more of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior ... Read more to moving your appliance.

Shut off water and disconnect hot and cold hoses. Use nut driver to remove three screws at back/top of washer. Slide top of washer back and up to remove. Use pliers to loosen band clamp on rubber hose and pull away from valve assembly. With fingers, disconnect wiring from hot and cold solenoids. Use allen wrench to remove valve assem ... Read more bly from frame of washer. Use reverse order to install replacement valve, although you can leave the top off the washer until you've checked for leaks.

repair was a cake-walk with the video there to help.Thanx

Replaced water pump

It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the sp ... Read more ace you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.