MHWE201YW00 Maytag Washer - Instructions

replaced the hot water valve

I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.

open the door of washer lined up baffle pushed down on baffle slid into place in 1 minute

you need to take off the front panel of the washer to do this repair, start at the top cover the bults are in the back, then the bottom panel on the front, then the control panel needs to come off, after all 3 of those are removed you can get to the front panel the door
the door lock also needs to be removed to get this panel off, then a couple small bults at the top of the panel.
once everything is removed you can start take off the old boot.
start with the front boot seal spring clamp using a flat head screwdriver then remove the boot from the inner drum. then the back boot seal clamp will be removed before you can pull the boot off of the washer
installing the new boot I think you should start with inserting the inner seal first then put in a silicone caulking before you pull the outer seal on the inner drum. once that is on re install the clamp and move to the outer seal
this you can use an extra set of hands if someone is around if not it is possible to do it yourself, you will need 3 flat head screw drivers to work the front boot seal spring clamp into place. make sure that is seated well before you start to reinstall the door and other panels
good luck

Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.

I just took off the old part and installed the new one. The new part was a bit different.

Since i knew the filter was cleared of obstructions I knew the code issue was something more serious. After consulting with local repair reps I decided that the drain pump was beginning to slow down causing the faults. First, I took the lower front panel off the front of the washing machine so that I could drain the water out of the plumbing. After draining the water out of the pump into a pan, I went ahead and then lifted the front of the washer (and dryer on top of it) and tilted it back far enough so that my wife could place some blocking under the front of the washer. I did this so that I could access two screws on the bottom of the pump. First disconnect the wire socket connection to the motor. Make sure power is off before doing this. There is plastic clip holding the wires to the motor that may need a screwdriver to pry it apart for removal. There are two 1.5" long screws holding the pump to the frame that require at least 4" of space so that you can remove them with a socket. After removing the two pump screws I disconnected both pump hoses from the pump. This requires pliers for one clamp and screwdriver or nut driver for the other clamp. My machine originally came with one clamp that could not be removed, so I had to use a dremel with a stone to cut the clamp. You have to be careful to not damage the hose when cutting the clamp if it cannot be removed with tools. I replaced it with a 2" typical standard stainless steel hose clamp. Carefully wiggling the pump while pushing it to the side it will loosen up so that the front of the pump can be pulled up. One side needs to have the plastic plate pried apart from underneath and after removing it the pump will come free to lift out. Reverse the removal process for re-installation. It is a little tricky holding the squeeze clamp open while pulling the hose onto the pump, but it is not too difficult. Before putting the front panel on run one load of laundry to make sure there are no leaks. Once you find there are no leaks, then tilt the machine up and back to reattach the front panel. It is much easier to do it this way than with the machine on the floor since the panel screw are on the bottom of the panel at floor level.

First tilt the washer back so you can drain water from the lines to the pump and the pump itself. Disconnect the lines with a pair of pliers and use a screwdriver to move the rubber stopper so that the pump will move to the right. With pump now in position to lift up and out of the washer , do it so you can disconnect the wire assembly. Replace the pump starting with the wires, then slide it in place and secure it with the rubber stopper. Attach the lines and make sure they are well sitted and clamped. set on feet and you are ready to wash.

As video instructed

Took it old pump and replaced with new pump VERY EASY

Replaced drain pump took longer to soak up water than actually replacing the pump motor with mine having the pedestal underneath I did not have to tip the washer at all so it was fast and easy. Three screws taking the front cover off a screwdriver lifting the Rubber and sliding the motor off and pair of pliers 4 to hose clamps making it a breeze.

Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

just changed out the pump. easy

Unplugged washer , used shop vac to drain water through drain hose on washer. Removed both hoses from old pump. Removed electric plug, removed 2 screws from bottom of the pump. Then reverse the process.