Models > MGR7662WS3 > Instructions

MGR7662WS3 Maytag Range - Instructions

All Instructions for the MGR7662WS3
46 - 60 of 131
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Rear Drawer Glide
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.
Parts Used:
Rear Drawer Glide
  • Ed from Maple Grove, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
Light Bulb - 40W
  • Yafa (and David) from Bothell, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
5 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom piece of range rusty
took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one
Parts Used:
Trim, Lower (White)
  • Bruno from LE ROY, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter stopped sparking.
I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!
Parts Used:
Bake Igniter
  • David from EDEN PRAIRIE, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken spring hinge
the door came apart fairly easy getting it all back together was another story lining up glass and panels that have already been heated was fun but its back together and working fine.... It should be noted that I have a warranty for the stove but the hoops I had to jump thru and the time it would take for the tech to come it was easier to do it myself!!
Parts Used:
Door Hinge - Active With Spring
  • Ralph from TEATICKET, MA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
temp sensor went oven not heating
the hardest part was moving stove to trplace part
Parts Used:
Oven Sensor
  • patrick from HUGHESTOWN, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Parts Used:
Oven Sensor
  • Gary from PLUM CITY, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
You
Pleaae prepopulate the manufacturer and part i purchased. I fix a lot of appliances so cannot expend the effort to decipher this.

Be well.
Parts Used:
Vent Trim - White
  • Ron from CARIBOU, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove would not light due to faulty electronic ignighter
Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.
Parts Used:
Bake Igniter
  • Victor from SAINT PETERS, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door hinge fell apart
Watched a video first. The repair was easy.
Parts Used:
Door Hinge - Active With Spring
  • myron from west salem, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not completely heat up, only heating to about 150 degrees Temp.
contracted a repair service person
Parts Used:
Bake Igniter
  • Isaac from MATTESON, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas oven would shut off mid cook
Removed grills. Removed bottom plate.
Removed flame shield.
Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
Parts Used:
Bake Igniter
  • Glenn from ROANOKE, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas oven interment lighting. Pan was cracked and out of shape.
Loosen top two rear screws from the top pan. Remove top pan
Remove 2 front screws from bottom pan. Remove bottom pan. Reverse order.
Replace both pans.
Parts Used:
BAFFL-BRNR
  • Teddy from PRAIRIEVILLE, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
WOULD NOT HOLD DESIRED BAKE TEMP
REMOVE BOTTOM OVEN PAN. REMOVE GAS DEFLECTOR. REMOVE GAS TUBE. UNPLUG WIRE. REMOVE TOP AND BOTTOM SCREWS ON IGNITER. REPLACE IGNITER AND REATTACH IGNITER SCREWS. RE-INSERT IGNITER PLUG. REPLACE GAS TUBE AND DEFLECTOR. REPLACE OVEN BOTOOM PAN.
Parts Used:
Bake Igniter
  • WILLIAM from SAINT JOSEPH, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Active spring broken
Removed the oven door listened to a video/You tube and the rest was easy.When you remove the door panels make sure all the parts are assembled correctly.
Parts Used:
Door Hinge - Active With Spring
  • Angelo from NAPLES, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MGR7662WS3
46 - 60 of 131
Back to Top