MFB2055DRE00 Maytag Refrigerator - Instructions

Unfortunately, I have still not managed to complete the repair, using the two parts indicated above, nor with the door bracket (part no WP2183805) that I ordered subsequently that arrived two days ago. It is not the same as, nor functionally equivalent to, the old bracket that I assumed was broken, since it was not retaining the piece in the base of the door into which the cam is inserted to mount the door. The new Cam is the correct part, but is not the solution since the old Cam is slightly worn but not damaged, and the thimble I bought does not seem to fit anywhere. The hole in the new bracket has a much too small hole to retain the Cam receptacle piece in place in the base of the door. However, this is the only lower door bracket shown in the PartSelect diagram of all the door parts used on a Whirlpool WRF560SMYM04 refrigerator. I do observe that the dark gray plastic cover on the base of the door is broken, but I don't imagine this plastic cover served to retain the Cam receptacle piece solidly in place, and this plastic cover is not offered as a replacement part either. At present I am at a total loss for how to proceed! However, the instructions for removing and replacing the door are clear and very easily carried out, and the job would be very quick and easy with the right parts. So beware if you are repairing the door on this model that the door parts diagram might not show all the parts to cover the door variations that apparently have been used!

Wrong thread size on bulb, as incorrect item sent. Refund processed and netted approx. $9.00 back after $9.00+ shipping and my return shipping of $5. Will never ever use your company again.

From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small pierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!

took the old thermistor out and put the new one in.

Easiest repair ever! Took maybe 5 minutes. Use the flathead screwdriver to push down on the three tabs holding the track onto the glass shelf and gently remove the old track. The new track snaps right in. Put the shelf back in the fridge, slide in the tray and it's done!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

I read the other comments on how easy the repair was, followed their advice, and it worked like a charm. Just use a screwdriver or butter knife to pop the track off the shelf and pop the new one back in.

The hardest part was getting the items in the refrigerator out of the way!

Unscrewed the old one and put the new one in
Some water on shelf of fridge
Overall not bad

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid