MDG6700AWM Maytag Dryer - Instructions

I had a problem a couple of months ago with the dryer not heating and replaced the thermal fuse after checking the the parts with a voltage meter and the dryer worked fine. When I did the repair I also cleaned all the lint out of the dryer, exhaust, and the vent. It worked fine. A couple of weeks ago my wife commented about how hot the dryer was and it seemed unusual. I realized there was another problem but before I could check it, the dryer stopped heating again. Some time ago, the sensor dry funciton quit working so I just went ahead and changed all the electronic componets, the two on the exhaust tube and the two on the heating tube. I assumed the high limit thermostat failed. After unplugging the dryer, I took the two screws loose on the top backside of the dryer that hold the top in place and removed the top, sliding it back. I removed the four screws holding the control panel in place and rotated the panel forward, then up and out of the way. I removed the four screws along the top of the front panel, then the ones from around the opening on the front, and the front door. There was one screw that held the heating tube. I removed it and the tube slid forward. I took the front wire lose and rotated the tube clockwise to pull it out and took off the back wire and changed out the thermal fuse and thermostat. The exhaust tube was right there in the front and all I had to do was change out the parts on it. Everything went back to gether as easy as it came apart and when I plugged the dryer back in, it worked just like new.

Replace the igniter and dryer did light and after 3 minute went out. so I ordered to gas valve selenoid's and replaced those and everything it working properly

Remove 2 screws which hold dryer/washer together on back. Remove 2 screws back top dryer and slide top back. Remove 4 screws top dryer that hold timer panel. Remove 6 screws that hold front panel on..4 on top of panel and 2 inside door. Disconnect wires to door at slide connection. Unplug dryer..this is actually 1st step. Remove 1 screw on heating element (lower right). I found that by removing the red wire the element will wiggle loose and come far enough out to disconnect black wire. There are 4 other terminal connections which are jumpers that will slide out with element. Note where wires attach and remove all. Use Multi meter on highest ohms setting or a continuity tester to test heating element - thermostats - thermal fuse. They should all have continuity between terminals. Replace any that don't . My thermal fuse was open (no continuity). I replaced it and had heat..but inadequate heat. Got new thermostat which fixed problem. Video I watched said to replace them together..I guess he was right. I suggest that while you have dryer pulled out to take time to check/clean dryer vent..also flapper outside.(mine had lint built up in hinge and prevented flapper from closing letting cold air and anything else in). Parts Select has great videos/skematics and even with "snail mail" delivery part was there in 2 days. They are the best!!

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

Dryer was real easy to get into, there are two 1/4" screws on top back of dryer that you can take out to take off the top. The elec. control board is on the left front of mach. it takes about 2 or 3 mins. to take out with a screw driver. I suggest that you go ahead and pull front of dryer off and clean it out if possible as the inside of mine was full of lent. There are only 4 or 5 screws holding the front on, the door will come off with front cover. It is also very easy to check all the sensors and the heating element if you have a multi meter. I hope this will help Oscar

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

The Maytag dryer had a removable front panel so it took only about 15 minutes to remove the front, replace the blocking plug and orifice and reinstall the front panel. I gave the repair time as 30-60 minutes since I took the time to vacuum the interior and clean the flame sensor. Great instructions were included with the kit.

after removing 2 screws securing top of dry i isolated the humming noise to the electronic board. Dryer would not turn on but drum light would work. 2 screws hold the electronic mount, and 1 screw hold electronic board. all electrical connection on board easily unplugged. connected new board installed in mount with 1 screw and then installed mount with two. plugged in and pressed power switch and electronic timer came up and dry started at the press of cycle start knob. the key to this repair was the stuck relay humming sound being generated by the either the relay or transformer on electronics control board.

The repair was pretty easy to install the heat element, but had to replace several other parts do to the manufacturer that had broke off

IMPORTANT!!! Unplug the unit first!! 1 - Remove two screws on the back of the top of the unit. Pull back a little on the top to release it from underneath the control unit on the front of the dryer (the piece with the dial and buttons). 2 - Remove the four screws from the control unit. They are located at the top of the dryer. Pop off the control unit - don't worry about breaking any wires as there are none. 3 - Remove the front of the dryer by removing the four screws that are NOT used for the door and door latch. I had also removed the door latch and door but I don't think it is necessary to remove them. The front will swing out from the bottom where you can unhook it and remove it. 4 - the heating element is located on the front of the unit, bottom right. Either draw a diagram of the wires or take a picture of them with your cell phone. Smart phones are great for this as you can zoom the picture if necessary. Remove the wires (they just push on but it may take some effort to get them off). It's either one or two of the wires that are not part of the wiring harness and they go from one part of the element to another so don't get excited if these wires fall down - you haven't done anything wrong, they are just loose. The one screw in the front holds the element in (the back of the unit just rests in that hole). Remove the screw and pull the unit out. Put the new element in, hook up the wires before positioning the element. Put the screw back in that holds the element and put the rest of the dryer back in the reverse order.

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

I verified that the thermistor was bad by testing the resistance. My manual said it should be 10K ohms at 78F. I was reading over 30K ohms. This is what caused the thermostat to blow, as the thermistor was telling the dryer the air temp was a good 30 degrees cooler than it actually was. You can also verify the thermostat is bad by checking it for continuity. I removed the screws on the top-back of the dryer and slid the top back to reveal the screws holding on the control panel. I removed those and popped off the control panel. It required a good bit of force. I then removed the four screws holding the front piece on and removed it by pulling it slightly towards me and up. The parts are located on the bottom right. They were underneath a black plastic flap on my dryer. I removed the cables and the took both parts out with a screwdriver. I replaced them with the new ones (they should only fit in the right slot) and reattached the cables. From there, reassemble in reverse of the disassembly.

Took the top back screws off (2) then pulled the top toward me and it came off. This left four screws that hold on the front control panel. I took out this four screws, which the control panel came out. You will then have to disconnect the door switch. Then I took off the front door, which which has two screws. Then I took the four screws out of the front panel,which are all on the top below the front control panel. You then have to pull up on the front panel to lift it up, it is sitting on two slots. This will give you excess to the heater. There will be one screw take it out and the heater will pull out also there will be six wires that you will have to disconnect so pay attention where they go (write it down.) You will have thermostat 2 and 3 and heater switch. Test them with a ohmmeter, my thermostat 3 was bad. There will be two screws to take out to replace the part. Put the wires back and put the dryer back together like you took it apart.