MDB8989SHZ0 Maytag Dishwasher - Instructions

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done

Total repair time after watching videos was 53 minutes. I estimate I saved between $200 to $300 by doing this myself. If you have any DIY skills, don't hesitate to replace the detergent dispenser yourself.

Turned off water supply to the unit. Removed plastic cover at bottom front. I only had to disconnect the copper water line to slide the unit about 1/3 of the way out. I then was able to reach the wires, disconnect them and use a stubby box/open end wrench (5/8? don't remember for sure) to remove the plastic nuts. I then opened the door, removed the bottom basket and slipped the element right out. Installation of new part was reverse.

Upper tray removed and each rack adjuster removed and replaced one after the other. Only tool was screwdriver. Only knowledge was from the online videos. Only took 30 minutes or so. The repair could have been done more quickly if I wasn't fearful that the smaller plastic parts would break when pulled or pried away from the rack adjuster. The only mistake was not making sure the adjuster tabs were fully engaged in back and clicked in the front attachment.

Had to remove 2 screws fastening dishwasher to counter. Also removed bottom faceplate to expose the legs and to be able to lower them. Other sites recommended disconnecting the drain and water line but I did not have to do that, I had enough slack in the lines. I got the dishwasher about halfway out of the cabinet and then was able to remove the 4 screws holding the right track. Put the new track in and was good to go. Problem was that the left track broke and fell off a few days later. Still was an easy fix and thanks to PartSelect it was not very expensive.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.

This was so simple! Some plastic tabs snapped off the upper rack adjuster in our dishwasher (which is not even 4 years old, so you can see how crappily made these things are), rendering the entire appliance unusable since the water sprayer thingie attaches to the underside of the upper rack. I was able to easily find replacement rack adjusters on PartSelect and thanks to the repair video, was able to install them in about 20 minutes. Most of that was rewinding the video since I had trouble getting the broken adjusters off! So delighted to have been able to do this myself and avoid paying $$$ for a repairman call out and replacement parts.

I ordered the part from this website and easily replaced it.

Watch video and followed instructions. Very easy!

Replaced door latch

removed and installed cords with screw driver

Pulled out dishwasher, removed 4 bolts holding the track to the dishwasher, replaced track and installed the 4 bolts. Pushed back the dishwasher and works like new. The new tracks are riveted instead of spot weld and will last longer.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!